Re: Graphics cards: PCIe 1.1/2.0 16 lanes showing as x8 or x4 in modern motherboards

Posted on 2024-06-07, 17:15

by

by mockingbird

in Milliways

in Milliways

Nexxen wrote on 2024-06-07, 15:10: I'd like to further the topic but on a dedicated forum. Any suggestions? No. I have been on the internet for 25 years, VOGONS is the only forum I recommend.

---

Re: Graphics cards: PCIe 1.1/2.0 16 lanes showing as x8 or x4 in modern motherboards

Posted on 2024-06-07, 12:38

by

by mockingbird

in Milliways

in Milliways

I thought that speed and links were independent from any drivers. Unless it's a Gpuz and HW are both wrong at the same time. When you run GPUZ, there is a "?" next to where it says "bus interface". Click that and run the render test... Does your PCIe speed change when you do this? Mine shows @16 …

---

Re: Graphics cards: PCIe 1.1/2.0 16 lanes showing as x8 or x4 in modern motherboards

Posted on 2024-06-05, 14:05

by

by mockingbird

in Milliways

in Milliways

I tried everything but no change. Force Gen 1/2/3... no change, lanes stay the same amount. With all the changes even on cpu support with newer BIOSes, I wonder if it is indeed a compatibility issue. On my ancient Ivy Bridge board, I have to manually set my PCIe to Gen 2 on one of the lanes or else …

---

Re: Graphics cards: PCIe 1.1/2.0 16 lanes showing as x8 or x4 in modern motherboards

Posted on 2024-06-05, 12:29

by

by mockingbird

in Milliways

in Milliways

Fire Gl is @ 16x 1.1 - works @ 4x 1.1 Other cards 16x 1.1 works @ 8x 1.1 2.0 same @ 1.1...... Is this a compatibility issue with old + new? I'll test all these cards on PCIe 2.0 and 3.0 boards on i7 4th gen to check if it is. Do you have an option in the BIOS to force which PCIe generation is used …

---

Re: Advice needed for motherboard recapping

Posted on 2024-05-31, 22:09

by

by mockingbird

in Marvin \ General Old Hardware

in Marvin \ General Old Hardware

I've scrapped a similar P4 board with bad caps / chipset before and pulled a similar set of caps all in a row around the socket like that. May have been (M) matsushita caps as well, they all tested perfect and I kept them for re-use. Probably replacing the blue&gold caps by the inductors would get …

---

Re: SETMUL is incompatible with my CPU, alternatives?

Posted on 2024-05-31, 17:53

by

by mockingbird

in Marvin \ General Old Hardware

in Marvin \ General Old Hardware

SETMUL is in fact compatible with your CPU. You need to bridge two tiny points on the CPU to transform it into the "mobile" variant.

---

Re: Advice needed for motherboard recapping

Posted on 2024-05-31, 02:31

by

by mockingbird

in Marvin \ General Old Hardware

in Marvin \ General Old Hardware

johnvosh wrote on 2024-05-31, 01:55: Here's some better pictures of the caps around the CPU socket. Thanks for all the help! Keep these: Filename IMG_1407.JPG File size 755.55 KiB Views 151 views Good luck!

---

Re: Advice needed for motherboard recapping

Posted on 2024-05-30, 15:22

by

by mockingbird

in Marvin \ General Old Hardware

in Marvin \ General Old Hardware

The P4 board bad caps are marked, 6.3v 3300uf. And of course they are in the hottest airflow from the heatsink Use these . If the VRM high caps (to the right of the socket at the edge of the board are green with a "K" shaped vent, then leave them. If they're "OST" brand but look ok, they should be …

---

Re: Advice needed for motherboard recapping

Posted on 2024-05-30, 14:07

by

by mockingbird

in Marvin \ General Old Hardware

in Marvin \ General Old Hardware

For a soldering iron, look for something around $100 from Aliexpress that has both hot air and an iron. The better stations will have the hot air circulation fan in the station itself, whereas the more inexpensive ones have the fan inside the piece that you hold when blowing the hot air. ... Here …

---

Re: Advice needed for motherboard recapping

Posted on 2024-05-29, 14:06

by

by mockingbird

in Marvin \ General Old Hardware

in Marvin \ General Old Hardware

On these relatively newer (read: post 2003/4) motherboards you will need the hot air to first heat the VRM area from the back of the board because the large copper plane will suck up the heat from the iron. I suggest you perfect your method of removing/inserting capacitors before attempting this on …

---

Re: Corruption issue when using rloew's TRIM.EXE (TRIM utility for DOS) with FreeDOS FDISK 1.2.1/1.3.1 partitioned DISK

Posted on 2024-05-17, 21:08

by

by mockingbird

in Marvin \ General Old Hardware

in Marvin \ General Old Hardware

R.Löw's TRIM.EXE can't be used even though I managed to boot the PC into DOS. SSD Tool: Reports "successfull". But when checking Hex content the bytes are still the same as before and not "00". Samsung Magician (last working XP version 4.5 iirc): Reports that it can't detect a Samsung Drive. How …

---

Re: Philips Rhythmic Edge PSC703 install CD please

Posted on 2024-05-15, 00:37

by

by mockingbird

in Marvin \ Sound

in Marvin \ Sound

DSC_0002_reduced.jpg Specifically with the VLSI ThunderBird128 cards with the large chip pictured above, has anyone got PC/PCI working on it? I soldered on a header and attached it to my board, but I don't see any option in SB_INIT.EXE that allows you to specify that. It seems like a very decent …

---

Re: ECS UC4914-G - Requesting GAL chip dump

Posted on 2024-05-10, 01:54

by

by mockingbird

in Marvin \ General Old Hardware

in Marvin \ General Old Hardware

Hmm the ECS AL486 also has a GAL (16V8B) and it is connected to the VESA slot portion for sure, and appears to go to the waitstate/speed jumpers (not 100% verified, just looking at back of board, could be wrong)... maybe it is for same reason??? If so the board should work fine with just ISA cards …

---

Re: ECS UC4914-G - Requesting GAL chip dump

Posted on 2024-05-09, 19:27

by

by mockingbird

in Marvin \ General Old Hardware

in Marvin \ General Old Hardware

Tiido wrote on 2024-05-09, 16:05: I found my board and it is UC4913 rev2.0, similar layout and same UMC chipset but no PLD between ISA slots or anywhere else so, unfortunately, no luck factor this time 😒 Capacitors on it are 4.7µF for the most part, but there are few 10µF ones too. Thanks for …

---

Re: Looking for Radeon R5 240 XP Drivers

Posted on 2024-05-09, 01:47

by

by mockingbird

in Marvin \ Video

in Marvin \ Video

fastvan wrote on 2024-05-09, 00:07: Oh well. So much for that idea.. Thank ya Don't give up so easily. This might work. It supposedly supports some (or at least one) GCN 2nd gen variant... IF you'rs isn't detected, try force-installing it through device manager.

---

Re: ECS UC4914-G - Requesting GAL chip dump

Posted on 2024-05-08, 22:38

by

by mockingbird

in Marvin \ General Old Hardware

in Marvin \ General Old Hardware

I might actually have this board, although I am not 100% sure. I have definitely a UC41xx that has very similar layout. I will try to locate it tomorrow and if we are all lucky, it actually doesn't have the protection bit set and any bruteforcing is unnecessary. Gravis cards, for example are using …

---

Re: Tyrian freezes on VIA VP3 chipset

Posted on 2024-05-08, 14:46

by

by mockingbird

in Marvin \ Software

in Marvin \ Software

Paar wrote on 2024-05-08, 11:11: Just switched to 430VX chipset motherboard and everything works flawlessly. Yeah, I don't think VIA is misunderstood and actually not that bad. At least this particular chipset. Yea, but is it the VP3 that's flawed or is it the VT82C586B...

---

Re: ECS UC4914-G - Requesting GAL chip dump

Posted on 2024-05-08, 13:29

by

by mockingbird

in Marvin \ General Old Hardware

in Marvin \ General Old Hardware

georgel wrote on 2024-05-08, 06:34: They have code protection from dumping. Oh, ok... Seems like this board is a write-off then. Maybe I'll find a donor board someday.

---

ECS UC4914-G - Requesting GAL chip dump

Posted on 2024-05-07, 17:07

by

by mockingbird

in Marvin \ General Old Hardware

in Marvin \ General Old Hardware

I have this motherboard that I rescued from scrap, but someone plucked off the GAL16V8D chip. Along with the caps which they plucked off, they also tried to remove an SN74LS245N but I have a replacement for that. Can someone please provide me with a dump of the GAL? Thanks IMG_20240507_122930588.jpg …

---

Re: ESS AudioDrive (ES1868) - a surprisingly good ISA sound card

Posted on 2024-04-16, 20:05

by

by mockingbird

in Marvin \ Sound

in Marvin \ Sound

Ok, as long as it's working... I recommend something like playing through Doom for a while to test stability.

---