Re: Gigabyte GA-6BA motherboard not good for voodoo3

Posted on 2023-09-03, 08:50

by

by shevalier

in Marvin \ General Old Hardware

in Marvin \ General Old Hardware

1) how did you figure out the correct regulator is that one in the picture for AGP?, (and not the one on the left of the Orange heatsink ). 2) (thanks for telling to remove the regulator completely and soldering a cable to the middle pin), Did you have the same board with the same problem in the …

---

Re: Gigabyte GA-6BA motherboard not good for voodoo3

Posted on 2023-09-03, 04:55

by

by shevalier

in Marvin \ General Old Hardware

in Marvin \ General Old Hardware

This is the revision 2.9 motherboard, sadly those 2 jumpers were added by gigabyte on revision3. Gigabyte engineers had a clouding of their minds. Two voltage sources are not connected in parallel, only current sources are connected in parallel. :-( For normal operation, it is necessary to remove …

---

Re: Broken pin(s) on a 775 motherboard

Posted on 2023-09-01, 09:26

by

by shevalier

in Marvin \ General Old Hardware

in Marvin \ General Old Hardware

Mamba wrote on 2023-09-01, 07:22: but I am not sure what I should do. Do nothing, floating VID is "1"

---

Re: Broken pin(s) on a 775 motherboard

Posted on 2023-09-01, 07:09

by

by shevalier

in Marvin \ General Old Hardware

in Marvin \ General Old Hardware

Mamba wrote on 2023-09-01, 05:15: A getto solution like a wire into the missing VID3 hole? http://www.xtremesystems.org/forums/showthrea … 775-Motherboard Do not mind it http://www.pc-optimise.com/portables/pinmod/VID.png

---

Re: Super slocket-iii and Tualatin p3 1.4 SL657

Posted on 2023-09-01, 05:45

by

by shevalier

in Marvin \ General Old Hardware

in Marvin \ General Old Hardware

I should probably reisolate all the pins(used tape) I would remove those pins from the socket. These pins are not affect to capability with Coppermine. and check the AK4 bridge. Good idea! Or the MB(P2B-F) simply doesn’t want to work with this CPU and slotket. I don`t think so. If it started, then …

---

Re: Super slocket-iii and Tualatin p3 1.4 SL657

Posted on 2023-08-30, 16:15

by

by shevalier

in Marvin \ General Old Hardware

in Marvin \ General Old Hardware

The first time when it did boot, the first thing I did was to go into BIoS and looked at the vcore voltage and it reported 1.4v. Don’t know if the CPU is broken now somehow, but the motherboard still works with another CPU so that’s good :) Congratulations, the case has moved forward. Check the …

---

Re: A tale of Intel Pentium III and Trident CyberBlade i7 [Photo ultra heavy thread]

Posted on 2023-08-28, 03:56

by

by shevalier

in Marvin \ General Old Hardware

in Marvin \ General Old Hardware

VIA has been totally beaten yep, very strange chipsets they made((( https://u.cubeupload.com/roksana/EVERESTCacheMEMgif.gif This may be due to the use of the integrated video core, but the memory speed is more like a 100MHz FSB. Check for a more recent BIOS (even beta) and if the options are …

---

Re: Super slocket-iii and Tualatin p3 1.4 SL657

Posted on 2023-08-27, 14:34

by

by shevalier

in Marvin \ General Old Hardware

in Marvin \ General Old Hardware

Is it between a random Vcc pin and a random Vss pin on the socket on the slotket? For the CPU, it doesn't matter if it's 1.45V or 1.42V. Therefore, it is worth measuring behind the inductance on the main board. As a minus, you can use any connector shield, for example, the USB. PS. Yes, it is the …

---

Re: Super slocket-iii and Tualatin p3 1.4 SL657

Posted on 2023-08-26, 10:15

by

by shevalier

in Marvin \ General Old Hardware

in Marvin \ General Old Hardware

nizce wrote on 2023-08-26, 09:51: and the AK4 bridge I guess Rumor has it that there are Tualatins who work without that. But personally, I have not met. PS. The BIOS should already be Tualatin ready by the time the processor is inserted. It is better to start with Coppermine and update the BIOS.

---

Re: Super slocket-iii and Tualatin p3 1.4 SL657

Posted on 2023-08-25, 15:26

by

by shevalier

in Marvin \ General Old Hardware

in Marvin \ General Old Hardware

By the way, how its do ECS in 100 000 series of matherboard.

---

Re: Super slocket-iii and Tualatin p3 1.4 SL657

Posted on 2023-08-25, 06:02

by

by shevalier

in Marvin \ General Old Hardware

in Marvin \ General Old Hardware

Regarding 2. - Shouldn't I also isolate AN3(I don't know why, just that everyone seems to have done that :D )? Everyone hopes that the float pin will pull the charge and there will be a logical "1". With all my tualatins, "1" is very erratic. After a couple of minutes, it often drops to "0". If the …

---

Re: Super slocket-iii and Tualatin p3 1.4 SL657

Posted on 2023-08-24, 05:28

by

by shevalier

in Marvin \ General Old Hardware

in Marvin \ General Old Hardware

Always said, no slotket - no problem. Aopen Mx3s - 150FSB with P3-s 1113. Cubx-L - 133FSB with the same P3-s. Except perhaps not with 1GB of RAM, because I can’t find last stick of RAM PC133 with CL2.

---

Re: Super slocket-iii and Tualatin p3 1.4 SL657

Posted on 2023-08-23, 11:52

by

by shevalier

in Marvin \ General Old Hardware

in Marvin \ General Old Hardware

I don't think. High-frequency Coppermine also consumes a lot of energy. And probably more than the Tualatin cores? https://www.mouser.com/catalog/specsheets/intel%20corporation_24445209.pdf p 28 vs https://datasheet.octopart.com/RK80530KZ012512-Intel-datasheet-11890764.pdf p19 The difference is …

---

Re: Super slocket-iii and Tualatin p3 1.4 SL657

Posted on 2023-08-23, 11:14

by

by shevalier

in Marvin \ General Old Hardware

in Marvin \ General Old Hardware

I don't think. High-frequency Coppermine also consumes a lot of energy. I have not seen such that Copper would work on bus 133, but Tualatin would not. There are rumors that this may be a problem with the Vtt power supply on Asus motherboards. But, again, I have not seen this. On a correctly …

---

Re: Super slocket-iii and Tualatin p3 1.4 SL657

Posted on 2023-08-23, 06:19

by

by shevalier

in Marvin \ General Old Hardware

in Marvin \ General Old Hardware

gets stuck under heavy load. A typical problem is when the adapter is not finished. Or Din_oe "pulls" and periodically the supply voltage drops to 1.3 Volts. Or Vtt_power_good is not pulled up to "logical 1" and the CPU disconnects the AGTL bus from the northbridge. Usually, either both work on bus …

---

Re: Super slocket-iii and Tualatin p3 1.4 SL657

Posted on 2023-08-23, 03:55

by

by shevalier

in Marvin \ General Old Hardware

in Marvin \ General Old Hardware

As with any popular (albeit long-standing) topic, a more of urban legends was born. 1. Check connection G35 to G37 at socket. At any copermine-ready system its must be connected by default. But there are exceptions, so you need to make sure. All Vtt does not need to be checked, it is enough that it …

---

Re: Abit BE6-II turns off after 3-5 seconds.

Posted on 2023-08-20, 13:47

by

by shevalier

in Marvin \ General Old Hardware

in Marvin \ General Old Hardware

i have mendocino on slotket and cu-mine normal cpu, not slotket. Both V_cpu=2,08V. VID4 in RC5058 is not grounded - no connection I never heard of Cu-mine with 2V V_core - 1.75max By the picture, VIDs on RC5058 come from DM74LS374. This is related to Jumper Free Configuration Control, including V_ …

---

Re: Abit BE6-II turns off after 3-5 seconds.

Posted on 2023-08-20, 05:49

by

by shevalier

in Marvin \ General Old Hardware

in Marvin \ General Old Hardware

In appearance, everything is fine. Except V_cpu. According to the datasheet on RC5058, 2V is all VID = 1. Those the CPU is not inserted. Or the signals from the slotket to the RC5058 do not pass. Check the jumpers at slotket. This is a pinout for Tualatin, I have not found another in normal quality. …

---

Re: Ultimate AGP Machine ( Windows XP ) Project - "Retrozaur" aka "Retrosaurus"

Posted on 2023-08-19, 08:37

by

by shevalier

in Marvin \ General Old Hardware

in Marvin \ General Old Hardware

Does it affects most of these X-Fi cards ? Its affect ALL pci x-fi. What's the problem ? Usually the sound starts to break, then the card generally ceases to be initialized. This is the main power capacitor DSP X-FI. No capacitor - no X-Fi I have the same card, also with the fron panel, and i must …

---

Re: Ultimate AGP Machine ( Windows XP ) Project - "Retrozaur" aka "Retrosaurus"

Posted on 2023-08-19, 06:15

by

by shevalier

in Marvin \ General Old Hardware

in Marvin \ General Old Hardware

X-Fi SB0460 this, Asus also HBA. At the same time, I would not recommend using 5.25 bay. This one has mediocre performance, it is more for appearance. PS. If X-fi is buggy, I would recommend replacing this largest capacitor here. This is the genetic disease of all PCI X-fi`s. On some polymer, 3-6. …

---