VOGONS


Reply 2380 of 2390, by 640K!enough

User metadata
Rank Oldbie
Rank
Oldbie
MJay99 wrote on 2020-06-11, 11:57:

@1:13 in your video I can see this:
gusar.jpg

That's one of the questionable spots I was trying to point out. There is a similar one at 1:39, I think. They could just be solder "whiskers" that don't actually make contact with anything else, but it would be a good idea to take a look.

Reply 2381 of 2390, by shock__

User metadata
Rank Oldbie
Rank
Oldbie
kompas-rus wrote on 2020-06-09, 15:13:
shock__ wrote on 2020-05-19, 16:56:

Alternative is so simply break off the excess on the Vibra brackets, as I did 😉

Hi, as promised, I will give you 3 boards as a gift, write to me.
http://chipkin.ru/wp-content/uploads/2020/06/ … 218-rotated.jpg

Will do 😉 Seems like we briefly missed a chance, as I ordered 2 Pentagon 1024SL 2.2 boards from you 😉
I'll write you to your usual e-mail ... or do you prefer a PM on here?

Current Project: new GUS PnP compatible soundcard

[Z?]

Reply 2382 of 2390, by kompas-rus

User metadata
Rank Newbie
Rank
Newbie
shock__ wrote on 2020-06-14, 10:54:
kompas-rus wrote on 2020-06-09, 15:13:
shock__ wrote on 2020-05-19, 16:56:

Alternative is so simply break off the excess on the Vibra brackets, as I did 😉

Hi, as promised, I will give you 3 boards as a gift, write to me.
http://chipkin.ru/wp-content/uploads/2020/06/ … 218-rotated.jpg

Will do 😉 Seems like we briefly missed a chance, as I ordered 2 Pentagon 1024SL 2.2 boards from you 😉
I'll write you to your usual e-mail ... or do you prefer a PM on here?

https://chipkin.ru/product/3-gift-pcb-gusar-for-shock/

Reply 2383 of 2390, by 640K!enough

User metadata
Rank Oldbie
Rank
Oldbie

Before I forget, I thought I'd mention one observation about the RC-1 design, even though it's not likely to be integrated (we did agree to no changes unless something is broken): C14 should ideally be a low-tolerance C0G/NP0 part. It seems that these are usually stocked in 1206 or 1210 form, and can be a bit of a challenge to solder onto the 0805 footprint while still making reasonable contact. A slightly larger set of pads would make life a little easier.

Reply 2384 of 2390, by shock__

User metadata
Rank Oldbie
Rank
Oldbie
640K!enough wrote on 2020-06-19, 03:35:

Before I forget, I thought I'd mention one observation about the RC-1 design, even though it's not likely to be integrated (we did agree to no changes unless something is broken): C14 should ideally be a low-tolerance C0G/NP0 part. It seems that these are usually stocked in 1206 or 1210 form, and can be a bit of a challenge to solder onto the 0805 footprint while still making reasonable contact. A slightly larger set of pads would make life a little easier.

Sounds rather possible. Will look into that.

Current Project: new GUS PnP compatible soundcard

[Z?]

Reply 2388 of 2390, by kitten.may.cry

User metadata
Rank Newbie
Rank
Newbie
Synoptic wrote on 2020-06-25, 18:23:
kitten.may.cry wrote on 2020-06-25, 15:34:

Is the project canned?

No, why ?

Confused by "This project is closed to previous donors for now"
"No exceptions, no need to ask via E-Mail/PM or the like.", perhaps.

Reply 2389 of 2390, by Synoptic

User metadata
Rank Member
Rank
Member
kitten.may.cry wrote on 2020-06-25, 20:01:
Synoptic wrote on 2020-06-25, 18:23:
kitten.may.cry wrote on 2020-06-25, 15:34:

Is the project canned?

No, why ?

Confused by "This project is closed to previous donors for now"
"No exceptions, no need to ask via E-Mail/PM or the like.", perhaps.

It's not taking anymore contributors in exchange for cards, but the project is still going on.

Reply 2390 of 2390, by kitten.may.cry

User metadata
Rank Newbie
Rank
Newbie
Synoptic wrote on 2020-06-25, 20:14:
kitten.may.cry wrote on 2020-06-25, 20:01:
Synoptic wrote on 2020-06-25, 18:23:

No, why ?

Confused by "This project is closed to previous donors for now"
"No exceptions, no need to ask via E-Mail/PM or the like.", perhaps.

It's not taking anymore contributors in exchange for cards, but the project is still going on.

Well, that's good to know.