I think my motherboard is missing some parts. \ VOGONS

I think my motherboard is missing some parts.

Topic actions

Post a reply

First post, by Baoran

Posted on 2018-11-04, 00:21

Baoran Offline

Rank l33t

Rank: l33t
Posts: 2200
Joined: 2017-04-01, 08:39
Location: Finland

My FIC 486-VIP-IO motherboard that I just got recently seems to be missing something. It has holes labeled RN18, RN19 and RN20 where based on the manual you are suppose to put something to choose which type of cpu you are going to put on the board. Like for example you should insert something in RN19 if you want to install dx4 cpu.

Is there any way to get whatever is missing there or is the motherboard useless because of that?

Reply 1 of 6, by cyclone3d

Posted on 2018-11-04, 00:33

cyclone3d Offline

Rank l33t++

Rank: l33t++
Posts: 7919
Joined: 2015-04-08, 06:06
Location: Huntsville, AL USA

Its just a jumper/ 0 ohm resistor pack.

Yamaha modified setupds and drivers
Yamaha XG repository
YMF7x4 Guide
Aopen AW744L II SB-LINK

Reply 2 of 6, by ODwilly

Posted on 2018-11-04, 00:35

ODwilly Offline

Rank l33t

Rank: l33t
Posts: 2317
Joined: 2013-06-18, 02:07
Location: Wa. U.S

From your description and picture I would say jumper pins are missing. Now it may be because the VRM components needed to use different voltage processors is missing as well. 5v vs 3.3v

Main pc: Asus ROG 17. R9 5900HX, RTX 3070m, 16gb ddr4 3200, 1tb NVME.
Retro PC: Soyo P4S Dragon, 3gb ddr 266, 120gb Maxtor, Geforce Fx 5950 Ultra, SB Live! 5.1

Reply 3 of 6, by Baoran

Posted on 2018-11-04, 00:37

Baoran Offline

Rank l33t

Rank: l33t
Posts: 2200
Joined: 2017-04-01, 08:39
Location: Finland

cyclone3d wrote:
Its just a jumper/ 0 ohm resistor pack.

Where I can get those?

Reply 4 of 6, by quicknick

Posted on 2018-11-04, 17:11

quicknick Offline

Rank Oldbie

Rank: Oldbie
Posts: 634
Joined: 2017-10-30, 23:53
Location: RO

Replace with 4 loops of solid wire. See here
This works for a quick test. The more elegant solution (beside finding a 0 ohm pack) would involve this

Reply 5 of 6, by Baoran

Posted on 2018-11-04, 17:44

Baoran Offline

Rank l33t

Rank: l33t
Posts: 2200
Joined: 2017-04-01, 08:39
Location: Finland

Did I understand correctly that not all the holes are suppose to be connected to each other and you only connect ones next to each other in pairs?

Reply 6 of 6, by quicknick

Posted on 2018-11-04, 18:13

quicknick Offline

Rank Oldbie

Rank: Oldbie
Posts: 634
Joined: 2017-10-30, 23:53
Location: RO

Absolutely. I have the 486-VIP-IO and I've just measured the part (Yageo 8B000J). It's exactly 4 individual jumpers (0 ohm resistors) in line.

Go to top of page Go to top of page

Back to General Old Hardware

Main menu

Common searches