Re: got a new card , vlb card.
Posted on 2013-06-30, 14:16
Ok Badmofo, show us a photo and share the beauty with us.
Re: got a new card , vlb card.
Posted on 2013-06-29, 20:19
I would not know what performance the AX has but W32i and W32P are pretty good dos performers.
Re: Windows XP is now "old". What are you doing?
Posted on 2013-06-29, 18:20
Well at my work 90% still use copy of xp instead of win7, and if they do have it they are crying for most older programs and drivers dont work as they need to. That would say enough i will be using xp for another 3+ years.
Re: Shuttle HOT-433 with 1 MB cache
Posted on 2013-06-29, 18:09
I am eager to know if it works. I also werent aware that i own two 32mb edo sticks that are3.3v according to spec sheet afterwards. The ali finali 1487,9 should be supporting these 3.3v, but there was no post at all.
Re: AT PSU +5V pin overheating at motherboard
Posted on 2013-06-29, 10:02
I was talking about the at psu. Check if the red 5v pins on the mobo are all connected to the same internal circuit, like should read 0ohms in between , and also check if the 5v wires of the at psu connector are all 0ohms and dont have any resistance in between. Also i really would resolder the at …
Re: AT PSU +5V pin overheating at motherboard
Posted on 2013-06-29, 06:37
It is due to a bad connection in the connector, there is resistance or sometimes contact which cause small spark and cause heat. Check it. The f1 is just a small fuse, we also use them at work, it will just blow not recover. Clean the contacts inside and on the mobo, also re-solder the connector at …
Re: Floppy drive benchmark (AHA-1542)
Posted on 2013-06-24, 18:56
I checked that section in my manual and it says to only use that jumper setting with double speed rotational fdd drive.
Re: Pentium 3 : Coppermine 1 ghz : Voodoo 2 SLI : Which Video Card?
Posted on 2013-06-24, 18:35
I see definitely 4 caps already bulging, they are so dead. If you like using the board ever again for good use replace them. If not you risk blowing your regulator circuit for the cpu.
Re: UM486/UM486SX need manual / question
Posted on 2013-06-22, 11:17
I have no more ideas, seems like you have it set as dx2-66 performance wise and looks like a dx 100. However i wouldnt mind to have a dx set to 100mhz 😉
Re: UM486/UM486SX need manual / question
Posted on 2013-06-22, 08:43
you can select no tests at startup and then you can do hardware mainboard info cpu info etc, just try out the program. btw what about the dos version msinfo? not sure. or norton system info.?
Re: UM486/UM486SX need manual / question
Posted on 2013-06-22, 08:03
it is running as a dx2 66 or 50 not sure, the integer performance (i mean the hardstones) of any dx2 66 would be around 29000 to 30000 and for dx4 100 it would be 40-45000, am5x86 133 would be around 53-55000. If you check the hardware and cpu at the other tabs and check twice you should be reading …
Re: UM486/UM486SX need manual / question
Posted on 2013-06-22, 06:17
some dx2's can run on 100mhz, amd's as far as i know. About older intels i amm not sure, dx2-80 they can do. the program probably reports back the wrong core clock maybe, can you check any fsb jumper that would be responsible for 50mhz setting instead of 33mhz. sometimes i use this tool, can you …
Re: Power Supply troubles
Posted on 2013-06-21, 18:58
The thing is not really about cold solder but failing filtering capacitors. They seem to look rather ok, some plastic is shrunk a lil by heat.so they already endured some power hours. The can have internal increased esr value and causes to behave badly at filtering the pwm dc signals on the 5v, 12 …
Re: Pentium 3 : Coppermine 1 ghz : Voodoo 2 SLI : Which Video Card?
Posted on 2013-06-21, 18:08
I would prefer a gf4 ti. Gf2 is too slow or you have to have a ultra lying around, it would be ok for a 500mhz system. I dont like the gf3, any gf4 ti would be excellent performance wise.
Re: SiS 486 Chipset Datasheets
Posted on 2013-06-19, 05:50
How can anyone tell which chip is capable of edo or not??
Re: Dell System 333P
Posted on 2013-06-19, 05:41
I have an DELL 333 but it is an sx 33. Are you sure that might you have an sx also that it is capable of sram upgrade?
Re: Dual Pentium Pro 200mhz - Compaq Proliant 850R Web Server
Posted on 2013-06-17, 20:10
What ram is in there 512mb !!!! Edo 72p or 168p ? I think a ppro is awesome there is not much improvement with 512k instead of 256k
Re: ISA Hard Drive controllers
Posted on 2013-06-15, 22:01
Me want to know too 😀
Re: 16MB 30-pin SIMM compatibility problems
Posted on 2013-06-15, 07:52
Good thing you have that awe32 and it is capable of testing 2x8bit ram, or 9bit in your case. As a 386sx would not be able to test the 2x16mb simm.
Re: 16MB 30-pin SIMM compatibility problems
Posted on 2013-06-14, 19:36
Youre right, and they are 5v. Well if they do not work in any system and you cannot make use for them, i would return them. Do you have a manual for those boards and the brand ram chips they maybe support in a compatibility view. Or you might want to install them in the awe32. Where did you get them …
Page 16 of 23