chiveicrook wrote on 2022-04-17, 14:16: Boot dos 6.22 from floppy and execute "fdisk /mbr" Alternatively, just install windows and it will overwrite mbr. Can't remember if dos installer also did this. It worked thx!

Hello , Recently i've decided to use dedicated 1.2 GB fujitsu hdd for dos , everything went fine , it have been formatted and fdisked as it suppose to be . It was given three partitions 500-500-222 mb . But when i try to boot it loading red hat linux which hes been installed before . I belive there …

Hello again mate i think vrm is totaly fine . And there is problem in other component . And its more likely HW monitor 99127f or associated elements . as i research lately 39 pin of as99127f is 5vsb detect so if there is 5v not present on this pin = no start . I suggest measure r13 it should be 470 …

Thanks man, much appreciated. I believe the orientation of the connector is wrong on your picture and color-coding though...this should be more like it, right? 24-pinP1.jpgatxpins.png If that is correct, I am only reading a resistance with my multimeter on the 5V pins (all of them) and ground, and …

Hey according your find it might be as99127f chip is dead picture i found so any rights goes @ http://monitor.espec.ws/section5/topic184611.html

Did you replace same capacity ? As i heard polymer capacitors have to be 2-3 times lower than electronic

I would recommend you riva tnt/tnt2 ,voodoo 1/2 . With celeron you wont get any benefit from more powerfull cards.

Hello, Just need some advice, I have this motherboard Zida Tomato BX440 based, tested and works fine, one of the best I have in performance, not the prettiest but good performance. But I noticed a bodge wire near the chipset a little flimsy, about to break, and I don't know if this is from factory …

Hey , It should be metal plate , you can also print it on self adhesive vinyl and siply put new picture on top of old one.

Are you sure ? I found it has 200mhz mem and core . Anyway i have original radeon R100 ill try it @ weekend.

What system youre trying install on ? Anyway since its PnP it should configure automaticaly unless there is conflict . As for standart IRQ its 7 or 5 and DMA 1 for SB. Anyway if you got OEM sb100 it might be driver issue.

hey mate, Halo CE and Morrowind is quite demanding games for your build i remember it was not that good on Athlon 1.4GHz with Geforce 3 and 9600PRO after . Was 15-40 fps @1024x768 at high settings.

Hey mate, How did you tried to clean ? Its hard to say what kind of liquid or what cause this . Anyway as C164,163,169 &190 its capacitors and theyre same as C211,210,169 &170 or C54,56, 94&95 . As for C31, C32, C103, C104, C106 its harder cause there is no reapeting elements

Thank you for reply . You are talking reasonable but there is still doubds as i found this pinout from PCCHIPS M598

Roman555 wrote on 2022-01-16, 08:03: Yes, I think so. But you didn't answer. My example: https://ptgmedia.pearsoncmg.com/images/chap7_9780789750006/elementLinks/07f […] Show full quote ciornyi wrote on 2022-01-16, 07:52: Roman555 wrote on 2022-01-16, 07:49: It depends how to count pins ) Where do …

Roman555 wrote on 2022-01-16, 07:49: ciornyi wrote on 2022-01-16, 07:43: Thank you for reply . I've updated full size board , and made measures for ground pins. Its mismatch pinout you privided me. It depends how to count pins ) Where do you think the pin #2 is ? Really ?Its counting always same …

Thank you for reply . I've updated full size board , and made measures for ground pins. Its mismatch pinout you privided me.

Hello retro fellas ! Just bought this board and find out it have audio onboard vibra16 vx chip. So i would be much appreciated to get manual or pinout for built in sound blaster.