Re: Hybrid 386/486 motherboard?
Posted on 2009-01-16, 23:22
Sounds similar except mine have 2 VLB slots. I can't be of any more help though.
Re: Hybrid 386/486 motherboard?
Posted on 2009-01-16, 20:58
I tried to figure it out but... I have 5 MB-4D50L (OPTi chipset) mainboards which have jumper settings and sockets for either 386, 486 or 486SLC, no manual. They are equipped with a 486DX-33 which they work with. I tried to make two of them work with 386s but it didn't work, the settings of some of …
Re: MMMMMMOWNED?
Posted on 2009-01-16, 16:58
A chance to move the compatibility database to the wiki? 😉
Re: GUS Classic Soundwave CD-45 daughterboard?
Posted on 2009-01-15, 11:29
Not even that. These are just a few low complexity digital ICs.
Re: GUS Classic Soundwave CD-45 daughterboard?
Posted on 2009-01-15, 11:06
This looks more like a CDROM port. A weird one as it's only 8-bit.
Re: 486 Motherboard Shipment Arrived
Posted on 2009-01-15, 02:23
That sounds like a good plan. You should test the board first though so you don't do the work for nothing. Take care of the polarity, + is pin1, - is pin4. From the photo it seems the acid has already spread at least to the 4-pin connector, so you should clean or replace that. After removing the …
Re: 486 Motherboard Shipment Arrived
Posted on 2009-01-14, 19:46
Don't do that, normal coin batteries are not meant to be recharged. Connect it to the 4-pin connector instead.
Re: Matrox Millennium 1 - no problems in DOS, but problems in Windows
Posted on 2009-01-14, 18:00
Same mainboard where the S3 failed? 😉
Re: 486 Motherboard Shipment Arrived
Posted on 2009-01-14, 17:54
Remove that battery...
Re: S3 Trio64v+ works in DOS not in Windows.
Posted on 2009-01-13, 15:51
This demo http://www.pouet.net/prod.php?which=1524 can make use of the S3 accellerator in DOS mode. Choose S3 accellerator and a video mode with 640 or more pixels width. If it doesn't work then the card is probably faulty...
Re: Die Siedler/ The Settler
Posted on 2009-01-13, 15:42
To check if the mouse works: Boot Windows while the mouse is connected, it should move the mouse pointer too. But while Windows uses it it can't be used by DOSBox. So restart Windows or remove the mouse from the device manager (you can add a /noserialmice to your boot.ini if you don't want Windows …
Re: Die Siedler/ The Settler
Posted on 2009-01-13, 13:44
In dosbox.conf serial2=directserial realport:com1 (com1 or another serial port you put your mouse on)
Re: Die Siedler/ The Settler
Posted on 2009-01-12, 23:32
> has to use IRQ 4 No, the IRQ for COM2 on every PC is 3.
Re: Setting Dosbox refresh rate for 720x400 mode
Posted on 2009-01-12, 23:29
Text mode is 640x400 unless you use a CVS build with machine=vgaonly.
Re: Serial port and dos Mode command
Posted on 2009-01-12, 17:07
Use the mode command that comes with Freedos.
Re: Pentium IV based mobo and Windows 98?
Posted on 2009-01-11, 03:06
As NDIS is affected it is possible the bug only shows if some sort of network is installed.
Re: Detecting a CD
Posted on 2009-01-11, 00:19
d:\ not d:
Re: Asus 386 Mother board
Posted on 2009-01-05, 15:11
It has cache, so it's good. There is not much more to say about 386 mainboards...
Re: ATI Rage 128 Pro - it's only half alive.
Posted on 2009-01-03, 23:28
I think those IDs are carved into the hardware, not in the BIOS. Might be a different chip revision.
Re: Booting from PCI HDD controller card... not much likely, or.... ?
Posted on 2009-01-02, 18:36
Sometimes called SCSI too.
Page 115 of 198