VOGONS


Reply 20 of 28, by wiretap

User metadata
Rank Oldbie
Rank
Oldbie

Fit of everything on the latest revised panel. Drives aren't screwed in for the picture, but they have perfect alignment when screwed in, with minimal gaps to account for various manufacturers that deviate by +/- 1mm from the standard.

PXL_20220126_200245970.NIGHT.jpg
Filename
PXL_20220126_200245970.NIGHT.jpg
File size
955.38 KiB
Views
275 views
File license
CC-BY-4.0
PXL_20220126_200348386.NIGHT.jpg
Filename
PXL_20220126_200348386.NIGHT.jpg
File size
497.21 KiB
Views
275 views
File license
CC-BY-4.0
PXL_20220126_200532204.NIGHT.jpg
Filename
PXL_20220126_200532204.NIGHT.jpg
File size
505.93 KiB
Views
275 views
File license
CC-BY-4.0

Circuit Board Repair Manuals
My Project List

Reply 21 of 28, by ajacocks

User metadata
Rank Newbie
Rank
Newbie

This really is impressive. I created my own PC case a couple of years ago, but this is a lot more complex and flexible:

2202C091-62A1-42CD-93C4-3D946B24608E.jpeg
Filename
2202C091-62A1-42CD-93C4-3D946B24608E.jpeg
File size
1.68 MiB
Views
262 views
File license
CC-BY-4.0
8B72B2A0-E3AE-4415-9110-BEA764655A66.jpeg
Filename
8B72B2A0-E3AE-4415-9110-BEA764655A66.jpeg
File size
1.88 MiB
Views
262 views
File license
CC-BY-4.0

- Alex

Reply 24 of 28, by wiretap

User metadata
Rank Oldbie
Rank
Oldbie

Fixed the PC Chips M326 v5.2 386 board yesterday. I think this one is going in another spare AT case I have laying around so I can keep the 3D printed case smaller with a 486 SBC.

Had to replace the AT power connector since the 12V was corroded badly from the varta battery. Fixed some traces in that area, fixed another trace over by the 74F244N chip, and replaced the corroded AT keyboard connector.

PXL_20220127_203822117.jpg
Filename
PXL_20220127_203822117.jpg
File size
581.38 KiB
Views
232 views
File license
CC-BY-4.0
PXL_20220127_211653159.jpg
Filename
PXL_20220127_211653159.jpg
File size
1.19 MiB
Views
232 views
File license
CC-BY-4.0

Circuit Board Repair Manuals
My Project List

Reply 26 of 28, by wiretap

User metadata
Rank Oldbie
Rank
Oldbie

Not really sure what you could do on 150x150.. Maybe a 3.5" drive or two as your drive bays for a SBC style case. I don't have time to make completely new files to accommodate that, but the design files for the original stuff is all in this thread so you are free to edit them.

Circuit Board Repair Manuals
My Project List

Reply 27 of 28, by oso2k

User metadata
Rank Newbie
Rank
Newbie
wiretap wrote on 2022-04-14, 00:06:

Not really sure what you could do on 150x150.. Maybe a 3.5" drive or two as your drive bays for a SBC style case. I don't have time to make completely new files to accommodate that, but the design files for the original stuff is all in this thread so you are free to edit them.

Thanks! I'll have to put some time into that. 😁

Reply 28 of 28, by oso2k

User metadata
Rank Newbie
Rank
Newbie
oso2k wrote on 2022-05-03, 21:42:
wiretap wrote on 2022-04-14, 00:06:

Not really sure what you could do on 150x150.. Maybe a 3.5" drive or two as your drive bays for a SBC style case. I don't have time to make completely new files to accommodate that, but the design files for the original stuff is all in this thread so you are free to edit them.

Thanks! I'll have to put some time into that. 😁

Hmm the faceplate is just a tad over 275mm. That's bigger than the build volume of the Adventurer 4 (220 x 200 x 250mm) I was considering purchasing next. I might just try to rework the original instead.