VOGONS


VIAFSB - DOS FSB utility for VIA chipsets

Topic actions

Reply 100 of 111, by Xardion

User metadata
Rank Newbie
Rank
Newbie

There we go, it built successfully and ran under qemu, and after disabling the check_smb() call so I could run it with the -c option, I was able to get the config and verify it against the W211B datasheet, which looks good. I've attached the output from that command (I converted the tabs to spaces with expand on Linux).

Reply 101 of 111, by enaiel

User metadata
Rank Member
Rank
Member
Xardion wrote on 2026-10-03, 23:12:

There we go, it built successfully and ran under qemu, and after disabling the check_smb() call so I could run it with the -c option, I was able to get the config and verify it against the W211B datasheet, which looks good. I've attached the output from that command (I converted the tabs to spaces with expand on Linux).

Nice work! Fingers-crossed that it actually works with your board.

Xardion wrote on 2026-10-03, 16:44:

<snip>
I added some comments next to the table entries to denote what the Spread Spectrum setting was for that particular entry (since there can be duplicate entries for a given speed and there often isn't any notable difference otherwise), and realized that it might be handy to add a char *notes field to that fsb_rec struct that could be displayed using "-c | --config". It seems like all these PLLs have that feature, but I could see there being some other extraneous bit of info that might be useful for the user to know.

Yes, I've been meaning to add the spread spectrum so that you can see it when you list the available frequencies. Maybe next release.

H/W: VIA C3 DOS PC | PIII-S Tualatin Win98SE PC
S/W: VIAFSB FSB Util | VIAXFG SB Config Util

Reply 102 of 111, by Xardion

User metadata
Rank Newbie
Rank
Newbie
enaiel wrote on 2026-10-05, 02:54:

Yes, I've been meaning to add the spread spectrum so that you can see it when you list the available frequencies. Maybe next release.

Yeah, I wasn't sure how useful that would actually be, since I thought it just used the first entry it found for a given speed. But if you added that, and then a way to pick an alternate entry, like say adding '_#' after the speed to specify an "index" (i.e. if there were multiple entries for 75, 75 or 75_0 would pick the first one, 75_1 would be the 2nd one, etc)

Reply 103 of 111, by enaiel

User metadata
Rank Member
Rank
Member
Xardion wrote on 2026-10-03, 01:29:

@enaiel Just FYI, I opened an issue on your Github to add support for the W211BH PLL, and then submitted a PR to do that since I realized it is nearly identical to the W230, primarily just a different table and there's one bit that isn't set in the 2nd byte of the data register.

Merged PR and released new version. Thanks for your contribution!
As always,. the source and releases are available on GitHub: https://github.com/enaiel/viafsb.

v0.3.2
* Modified build and source files to add support for cross-compiling.
* Support for the W211BH PLL contributed by Vogons.org member @Xardion.

I added support for using a DJGPP cross-compiler from https://github.com/andrewwutw/build-djgpp. You just need to pass the cross-compiler in an argument to make as detailed in the new INSTALL file on GitHub. This has made my life much easier as I can now develop and compile on Linux or Windows with modern editors without even needing DOSBox. I just need to test it on my DOS pc.

H/W: VIA C3 DOS PC | PIII-S Tualatin Win98SE PC
S/W: VIAFSB FSB Util | VIAXFG SB Config Util

Reply 104 of 111, by Xardion

User metadata
Rank Newbie
Rank
Newbie
enaiel wrote on 2026-10-07, 13:29:

I added support for using a DJGPP cross-compiler from https://github.com/andrewwutw/build-djgpp. You just need to pass the cross-compiler in an argument to make as detailed in the new INSTALL file on GitHub. This has made my life much easier as I can now develop and compile on Linux or Windows with modern editors without even needing DOSBox. I just need to test it on my DOS pc.

I saw this on GitHub, nicely done! This would have been nice to have, compiling in my QEMU VM was quite slow 😁 Using DOSBox would've been faster for sure, but I was going for a period-correct experience!

Reply 105 of 111, by Xardion

User metadata
Rank Newbie
Rank
Newbie

Just FYI, I've been talking to @Dodobird (aka Retro Becanes on YouTube, who dropped a video on that Boser HS-6251 SBC I have on the way) via e-mail, and he let me know that he tested viafsb on his board (I won't have mine until next Tuesday), and was able to downclock the FSB to 83 Mhz without it crashing. This makes sense, because he'd have to change jumpers to take the PCI divider down to 2x (for 66 Mhz FSB), though this might be an option in the BIOS, the documentation doesn't say and I don't have one yet to check. So it looks like the W211BH support is working!

Reply 106 of 111, by Xardion

User metadata
Rank Newbie
Rank
Newbie

Looks like you can set that board to 66 Mhz in the BIOS (saw it was an option in his video), so he should have been able to do that to push the FSB under 83 Mhz.

Reply 107 of 111, by enaiel

User metadata
Rank Member
Rank
Member
Xardion wrote on 2026-10-08, 16:43:

Just FYI, I've been talking to @Dodobird (aka Retro Becanes on YouTube, who dropped a video on that Boser HS-6251 SBC I have on the way) via e-mail, and he let me know that he tested viafsb on his board (I won't have mine until next Tuesday), and was able to downclock the FSB to 83 Mhz without it crashing. This makes sense, because he'd have to change jumpers to take the PCI divider down to 2x (for 66 Mhz FSB), though this might be an option in the BIOS, the documentation doesn't say and I don't have one yet to check. So it looks like the W211BH support is working!

Thats awesome news!

BTW, I've been using my train commute time to develop on my Linux laptop now that I have cross-compiling enabled. I have already pushed a bunch of changes to GitHub. Will cut a new release soon.

H/W: VIA C3 DOS PC | PIII-S Tualatin Win98SE PC
S/W: VIAFSB FSB Util | VIAXFG SB Config Util

Reply 108 of 111, by Xardion

User metadata
Rank Newbie
Rank
Newbie

Excellent! Great changes btw, sorting the frequency tables, moving the config handling so you can validate a config on a system without an appropriate chipset, pll contrib instructions (would've been nice to have before, but it wasn't exactly rocket science to figure out). Good stuff man.

Reply 109 of 111, by enaiel

User metadata
Rank Member
Rank
Member

New version released. Being able to cross-compile on my Linux laptop has helped me develop much quicker!
As always,. the source and releases are available on GitHub: https://github.com/enaiel/viafsb.

v0.3.3
* Added support for PLLs W230H, W196.
* Fixed sorting of FSB frequencies in each PLL FSB frequency table.
* Added instructions on how to contribute support for new PLLs in CONTRIB file.
* Skip SMBus and PLL checks when using the print config feature.

mockingbird wrote on 2025-09-26, 18:46:

Would you please add support for Cypress W196?

Repo Man11 wrote on 2026-07-05, 00:33:

Hopefully you are still taking requests. I've a Tyan S1854 (Apollo Pro 133A) 694X-596B and a Cypress W196 PLL. Here is a link with the data sheet: https://theretroweb.com/chips/5784

marxveix wrote on 2025-08-06, 17:14:

Chaintech 7AJA2 has: Cypress W230H clock generator (PLL)

Added support for Cypress W196 and W230H PLLs. Please test when you get a chance.

Danger Manfred wrote on 2025-02-22, 23:51:

Amazing tool, could you try to add support for the Epox/ProNix EP-8KTA3+?

The southbridge is a VIA VT82C686B, and the PLL is this one: https://www.alldatasheet.com/html-pdf/179408/ … /HIP6301CB.html .

HIP6301CB is not a PLL - it's a microprocessor voltage regulator. Please look again for the PLL.

H/W: VIA C3 DOS PC | PIII-S Tualatin Win98SE PC
S/W: VIAFSB FSB Util | VIAXFG SB Config Util

Reply 110 of 111, by Xardion

User metadata
Rank Newbie
Rank
Newbie
Danger Manfred wrote on 2025-02-22, 23:51:

Amazing tool, could you try to add support for the Epox/ProNix EP-8KTA3+?

The southbridge is a VIA VT82C686B, and the PLL is this one: https://www.alldatasheet.com/html-pdf/179408/ … /HIP6301CB.html .

Mobile CPUs up to Athlon XP Barton are unofficially supported (only problem on my mobile Barton 2500+ is that the max FSB of the board is 133 and the max multiplier of the board is 12.5, so it won't go above 1.6 GHz, but at least it has twice the cache of previos generations. It also works with AMD Geode NX CPUs (highly binned Athlon XP Thoroughbred-B with unlocked multipliers, again up to 12.5), so in theory a wide range of speeds should be accessible.

That board actually has a W230-03H PLL, which viafsb already has support for. It's right here between the DIMM slots and the floppy connector.

Reply 111 of 111, by marxveix

User metadata
Rank Oldbie
Rank
Oldbie
enaiel wrote on 2026-10-12, 20:52:
marxveix wrote on 2025-08-06, 17:14:

Chaintech 7AJA2 has: Cypress W230H clock generator (PLL)

Added support for Cypress W196 and W230H PLLs. Please test when you get a chance.

This board needs some caps replacement at the moment, its waiting my return to this build, but i will try when i can.

Best ATi Rage3 drivers for 3DCIF / Direct3D / OpenGL / GLUT / DVD : ATi RagePro drivers and software
33+MiniGL / OpenGL Win 9x dll files for all ATi-Rage3 based cards : ATi RagePro OpenGL files