VOGONS


First post, by red-ray

User metadata
Rank l33t
Rank
l33t

I wish to get a Soyo SY-4SAW motherboard that supports EDO ram and gather some do and some don't, for now I have a Unicorn ENDAT-486PL, I wonder if 2 x 128MB EDO SIMMs will work. When I check with Google it says that the SiS 496 PR revision is needed for EDO.

If you have any SiS 496 based motherboard with working EDO memory please will you post the SiS 496 chip revision ?

file.php?id=251144

The different chip revisions report different PCI revisions, AFIK below is correct and have updated my SIV utility / pcidevs.txt with this information.

  • MU - PED2 - 94 - 02 - only FPM
  • NT - PFD1 - 94 - 10 - only FPM
  • NV - PEA0 - 94 - 20 - only FPM - early
  • OR - PFD0 - 94 - 30 - only FPM
  • OR - PGD0 - 95 - 30 - only FPM
  • NV - PGD0 - 95 - 31 - only FPM - late
  • PR - PHD0 - 95 - 40 - EDO + FPM - early
  • PR - PHD2 - 97 - 02 - EDO + FPM - early (late batch)
  • PR - PHD1 - 95 - 41 - EDO + FPM - late

file.php?id=251145

I suspect the BIOS may use the PCI revision to decide if it should set EDO Detect.

SiS 496 data in pcidevs.txt

1039:0496=496/497 i486 PCI Chipset
1039:0496:02== - MU or if EDO PR (late batch )
1039:0496:10== - NT
1039:0496:20== - NV (early)
1039:0496:30== - OR
1039:0496:31== - NV (late)
1039:0496:40== - PR (early)
1039:0496:41== - PR (late)

I posted asking about some of this some time ago and decided to create this thread so I could ask for more information without hijacking that thread, I intend to update this post as I find more information.

Last edited by red-ray on 2026-11-04, 15:11. Edited 21 times in total.

Reply 1 of 27, by red-ray

User metadata
Rank l33t
Rank
l33t

I am only interested in information about SiS chipset revisions.

Last edited by red-ray on 2026-10-23, 14:48. Edited 4 times in total.

Reply 2 of 27, by Disruptor

User metadata
Rank l33t
Rank
l33t

Perhaps this post can help you:
Re: Soyo SY-4SAW2 Rev WA3

Reply 3 of 27, by Disruptor

User metadata
Rank l33t
Rank
l33t
red-ray wrote on 2026-10-19, 13:05:

So far I have found Soyo SY-4SAWs for sale with the QR + RU + ST revisions and suspect that these are later than PR so should support EDO.

Sorry, but where do you read this board contains QR + RU + ST revisions?
I do not read anything about that revision on the description and the chips are couvered with stickers.
It also contains the warning: *No liability for techn. Data / *No Liability for Technical Information

Reply 4 of 27, by bertrammatrix

User metadata
Rank Member
Rank
Member

I was also searching for a SIS chipsetted board with edo support a few years back. All I can confirm is that PR worked with edo, and I don't think anything else did, though I can't recall if i had any of those "later" revisions to test.

In the end EDO support only brought a very very minimal improvement speed wise on this chipset - this is not where the holy grail lies. In my case I was running the board at a 60mhz FSB - and results were still dissapointing. At more common lower FSB speeds the advantage was almost nil

Reply 5 of 27, by Disruptor

User metadata
Rank l33t
Rank
l33t
bertrammatrix wrote on 2026-10-20, 17:33:

I was also searching for a SIS chipsetted board with edo support a few years back. All I can confirm is that PR worked with edo, and I don't think anything else did, though I can't recall if i had any of those "later" revisions to test.

In the end EDO support only brought a very very minimal improvement speed wise on this chipset - this is not where the holy grail lies. In my case I was running the board at a 60mhz FSB - and results were still dissapointing. At more common lower FSB speeds the advantage was almost nil

Your tests at 60 MHz match to the test of my pal mkarcher: 486 board with UMC 8881E/8886B: The winner is: EDO without L2 (if your only other option is L2 at 3-2-2-2)
Did you notice any difference in how many EDO modules you have tested and in the speed of the EDO modules on your SiS based mainboard?

He got best results with EDO when all L2 cache modules were NOT INSTALLED:
Memory(!) timing 3-1-1-1 at FSB 40 with 1 50 ns EDO module.
Memory timing 4-2-2-2 at FSB 60 with 3 60 ns EDO modules.

Reply 6 of 27, by red-ray

User metadata
Rank l33t
Rank
l33t
bertrammatrix wrote on 2026-10-20, 17:33:

I was also searching for a SIS chipsetted board with edo support a few years back. All I can confirm is that PR worked with edo, and I don't think anything else did, though I can't recall if i had any of those "later" revisions to test.

In the end EDO support only brought a very very minimal improvement speed wise on this chipset

Thank you for the information, for me speed is not the only reason I would prefer to use EDO, it's down to me already having 4 x 64MB of EDO SIMMs and I would like to have EDO for testing SIV 's SiS 496 reporting. I am also wondering what the EDO Detect bit does, does it just get set while detecting EDO SIMMs or does it remain set after the detection is complete.

Do you still have the PR and/or do you know the PCI revision please? Thus far I have also seen 0x31 from a friends NV 496 and 0x02, I don't know which revision reported this.

Reply 7 of 27, by bertrammatrix

User metadata
Rank Member
Rank
Member
red-ray wrote on 2026-10-20, 18:17:
bertrammatrix wrote on 2026-10-20, 17:33:

Do you still have the PR and/or do you know the PCI revision please? Thus far I have also seen 0x31 from a friends NV 496 and 0x02, I don't know which revision reported this.

Sorry I don't. I moved away from sis boards altogether and sold off whatever I had.

Reply 8 of 27, by red-ray

User metadata
Rank l33t
Rank
l33t
bertrammatrix wrote on 2026-10-20, 21:37:

Sorry I don't. I moved away from sis boards altogether and sold off whatever I had.

OK. Another thing I wish to check is if the Soyo SY-4SAW will work with a mix of EDO + FPM at the same time, I asked Google which said No, but I don't trust this is correct as, by default, it says also says No for my Intel VS440FX.

I would like to try similar to as below with a SiS 496 PR based system, I wonder what happens if you put EDO SIMMs in systems with other revisions. My DEC Venturis posts, but the reported memory size was less than it should be.

file.php?id=251236
file.php?id=251237

Reply 9 of 27, by Disruptor

User metadata
Rank l33t
Rank
l33t
red-ray wrote on 2026-10-22, 07:31:
OK. Another thing I wish to check is if the Soyo SY-4SAW will work with a mix of EDO + FPM at the same time, I asked Google whic […]
Show full quote
bertrammatrix wrote on 2026-10-20, 21:37:

Sorry I don't. I moved away from sis boards altogether and sold off whatever I had.

OK. Another thing I wish to check is if the Soyo SY-4SAW will work with a mix of EDO + FPM at the same time, I asked Google which said No, but I don't trust this is correct as, by default, it says also says No for my Intel VS440FX.

I would like to try similar to as below with a SiS 496 PR based system, I wonder what happens if you put EDO SIMMs in systems with other revisions. My DEC Venturis posts, but the reported memory size was less than it should be.

file.php?id=251236
file.php?id=251237

red-ray, the AI is not as smart as you.
As we know AI guesses a lot of things.
I think it guesses that mixing EDO and FPM in the same bank would not work. That is very likely, althought the AI does not tell about it.
But you are smart and have tried EDOs in one bank and FPMs in the other bank.
I'm not sure but perhaps the 430FX is able to run each bank with different timing. If, then it is likely that EDOs and FPMs both work at the same time - but in different banks.
A 486 just needs one SIMM per bank, but in boards with 4 SIMMs neighboured slots are somehow tied together, not to forget about the Saturn II which may do interleave then.
But it is worth a try. I don't know whether there is any 486 chipset that can do separate RAM timings on each bank - especially your favoured SiS 496.
Thank you for your post.

Reply 10 of 27, by red-ray

User metadata
Rank l33t
Rank
l33t
red-ray wrote on 2026-10-19, 13:05:

[*] PR - PHD2 - 97 - 02 - EDO + FPM - early (late batch)

I now have my new i486 SiSS 596 PR setup and working well, I noted:

  1. The PCI Revision on my SiS 496 PR is not as I expected, it 02 when I expected 40, this is very unusual, but I see the same in a 2019 SIV save file I have.
  2. The onboard VGA work not work @ 1024 x 768 x 16 so I "Fired up the Blackbird".

file.php?id=251983
file.php?id=251984

Reply 11 of 27, by Disruptor

User metadata
Rank l33t
Rank
l33t
red-ray wrote on 2026-11-01, 12:23:
I now have my new i486 SiS 596 PR setup and working well, I noted: […]
Show full quote
red-ray wrote on 2026-10-19, 13:05:

[*] PR - PHD2 - 97 - 02 - EDO + FPM - early (late batch)

I now have my new i486 SiS 596 PR setup and working well, I noted:

  1. The PCI Revision on my SiS 496 PR is not as I expected, it 02 when I expected 40, this is very unusual, but I see the same in a 2019 SIV save file I have.
  2. The onboard VGA work not work @ 1024 x 768 x 16 so I "Fired up the Blackbird".

file.php?id=251983
file.php?id=251984

Congratulations.
Have you checked the refresh rate of your onboard VGA @ 1024x768? Perhaps it is interlaced which will often not work on a LCD but on a CRT.
I've also noted your SIV displays 128 kB of cache.
Which board do you have? It seems the Soyo SY-4SAW does not have an onboard VGA.

Reply 12 of 27, by amadeus777999

User metadata
Rank Oldbie
Rank
Oldbie

I had this LS486SE-Rev.C2 running with EDO and it, too, has a 'PR'tag on the NB...

Reply 13 of 27, by red-ray

User metadata
Rank l33t
Rank
l33t
amadeus777999 wrote on 2026-11-02, 16:43:

I had this LS486SE-Rev.C2 running with EDO and it, too, has a 'PR'tag on the NB...

Thank you for your post, yet another PR variant, I wonder if I ever figure them all out. What I need to know is, "What is it's PCI Revision", it's in the PCI Config space at offset 0x08. I wonder can you boot Windows on it and check? , fingers crossed you can. Maybe you can boot MS-DOS and know of a DOS utility that can dump PCI config space, do you?

Reply 14 of 27, by amadeus777999

User metadata
Rank Oldbie
Rank
Oldbie
red-ray wrote on 2026-11-02, 18:29:
amadeus777999 wrote on 2026-11-02, 16:43:

I had this LS486SE-Rev.C2 running with EDO and it, too, has a 'PR'tag on the NB...

Thank you for your post, yet another PR variant, I wonder if I ever figure them all out. What I need to know is, "What is it's PCI Revision", it's in the PCI Config space at offset 0x08. I wonder can you boot Windows on it and check? , fingers crossed you can. Maybe you can boot MS-DOS and know of a DOS utility that can dump PCI config space, do you?

I have sold the board a few years ago when "moving house".
Currently I can't help as I do not own any SiS 49x based system.
Maybe I'll buy a board next month it it is still available - it's an ASUS PVI-486SP3. I'll ask the seller if the chipset is of the PR variant(can't determine it by his lousy picture).
Don't know any such utility but maybe one of us can develop a simple "mini tool".

Reply 15 of 27, by Disruptor

User metadata
Rank l33t
Rank
l33t

Please also ask for the PVI-486SP3's board revision.

Reply 16 of 27, by red-ray

User metadata
Rank l33t
Rank
l33t
amadeus777999 wrote on 2026-11-03, 21:40:

Maybe I'll buy a board next month it it is still available - it's an ASUS PVI-486SP3. I'll ask the seller if the chipset is of the PR variant(can't determine it by his lousy picture).
Don't know any such utility but maybe one of us can develop a simple "mini tool".

Thank you for your reply and OK about not having a system. I recently bought what the seller listed as a Socket 7 AT Motherboard SiS 486 pc tested working ISA PCI 2x EDO DRAM PS/2 which is as I expected, Socket 3, when I fed the dusty photo into GoogleAI and it managed to figure out the actual board after 4 or 5 incorrect attempts. I contacted the seller to ask it it was PR revision, it was and he also mentioned he had the PISA riser with 3 x AGP slots!, that are actually ISA. If post or PM me a link I will try and figure out what it is.

I have never programmed for MS-DOS and have no plans to. You could use my SIV utility if you install >= Windows 95 or NT V3.51. I have W2K + NT4 + W98 on my i486.

Reply 17 of 27, by amadeus777999

User metadata
Rank Oldbie
Rank
Oldbie

@Disruptor
The board is a revision 1.0 from what I can see.
I asked the seller to take a look at the north bridge or send a picture.

@red-ray
Thanks for your great utility - I downloaded it and we'll give it a try.
The link concerning the board is https://www.kleinanzeigen.de/s-anzeige/asus-p … 628356-225-6330
I think the little tag reads "OR"...?

Reply 18 of 27, by red-ray

User metadata
Rank l33t
Rank
l33t
amadeus777999 wrote on 2026-11-04, 08:55:

The link concerning the board is https://www.kleinanzeigen.de/s-anzeige/asus-p … 628356-225-6330
I think the little tag reads "OR"...?

Good luck, a save from a SiS 496 OR would be good, AFAIK I don't have one. Which OSes do you plan to install? I have W2K + NT4 + 98SE my Intel DX4-WT (P24C) 120MHz @ SK096 (I have a selection of CPUs)

Reply 19 of 27, by amadeus777999

User metadata
Rank Oldbie
Rank
Oldbie
red-ray wrote on 2026-11-04, 09:36:
amadeus777999 wrote on 2026-11-04, 08:55:

The link concerning the board is https://www.kleinanzeigen.de/s-anzeige/asus-p … 628356-225-6330
I think the little tag reads "OR"...?

Good luck, a save from a SiS 496 OR would be good, AFAIK I don't have one. Which OSes do you plan to install? I have W2K + NT4 + 98SE my Intel DX4-WT (P24C) 120MHz @ SK096 (I have a selection of CPUs)

Dos 7.1 as in W9x.
If I get the board at the end of the month I'll post an update and run the legacy exe of your info utility on it.
I have a book by Hans-PeterMessmer describing pc hardware... maybe there's some hints regarding a "PCI configuration dump".