Photo.

MKT_Gundam wrote on 2020-01-03, 22:47:

My P3BF v. 1.04 dont have the Jumper free/Manual header. Theres other way to enable or just my mobo revision? Tee BIOS vrsion i […]
Show full quote

My P3BF v. 1.04 dont have the Jumper free/Manual header.
Theres other way to enable or just my mobo revision?
Tee BIOS vrsion is 1006.
How i will set the dip switches for later cpus like pIII 800mhz or 1ghz?
The manual at ASUS site only show for p3 600 and below.

Jumperfree will be set when ALL dipswitches are set to ''off''. Settings should be available in bios after that.

If it doesn't work just use the switches? It's way easier than using jumpers on other boards....

Here
https://ibb.co/M7Mn115

https://ibb.co/ZV75LBN

https://ibb.co/M9kyLHR

https://ibb.co/pWnhztt

This board came with a slotket and pentium 3 600E
The slotket model is here:
https://ibb.co/7RYG5xz

The jumperfree block sits just above the control panel at the right side. It is marked with [JEN] and there is a blue jumper installed on pin 1 and 2. Move the jumper to pin 2 and 3 for jumperfree mode and adjust the dipswitches in the blue block as indicated bij Meljor.

PARKE wrote on 2020-01-04, 15:36:

The jumperfree block sits just above the control panel at the right side. It is marked with [JEN] and there is a blue jumper installed on pin 1 and 2. Move the jumper to pin 2 and 3 for jumperfree mode and adjust the dipswitches in the blue block as indicated bij Meljor.

Yup... missed the JEN jumper part but that's right.

BTW, the 800mhz cpu should be multiplier locked so just plug it in and make sure it gets the right 1.7v-1.8v and it should work unless your bios version doesn't support that core (in that case upgrade bios version).

He has the 1006 Bios and should be fine I think.

bx3f1006.zip P3B-F (Intel 440BX chipset) M/B, PnP BIOS ver. 1006 30/Jun/2000 1. Fix Windows 2000 cannot be installed if all Pn […]
Show full quote

bx3f1006.zip
P3B-F (Intel 440BX chipset) M/B, PnP BIOS ver. 1006 30/Jun/2000
1. Fix Windows 2000 cannot be installed if all PnP devices in Super I/O are disabled.
2. Support 566MHz and 850MHz CPU with clock ratio equal or greater than 8.5x.
3. Revise Coppermine Vcore limit for 128K cache Coppermine.
4. Fix Hardware Monitor false alarm of CPU vcore when using old celeron CPU.
[unquote]

Now checking my photos .....The JEN is really above the control panel headers :p.
The manual at ASUS site has a different layout.
Thnaks for the help guys!

I have a Asus P3 board and the jumper free mode does not work with all processors (the P3 550 E series I had issues with). Be sure to reset the BIOS if you cannot get the new cpu to POST.

MKT_Gundam wrote on 2020-01-04, 17:06:

Now checking my photos .....The JEN is really above the control panel headers :p.
The manual at ASUS site has a different layout.

The P3B-F manuals cover three versions of the board: no ISA, 1x ISA and 2x ISA.
Your board has 2x ISA and does not correspond 100% with the graphics in the 1.04 manual.