I think that most of them should fit. But to be sure, there's a need to check dimensions (datasheets) of DIMM SDRAM, DDR, DDR2, DDR3 etc. I bought some cheap ones from China and in description was mentioned that they'll fit in DDR1 and DIMM SDRAM's.

Yesterday I've received cheap RAM Heatsinks from China which are installed roght now. They aren't needed in this configuration, but this component now looks a lot better inside case ;) http://www.imagic.pl/files/2853/Pentium%20II%20333MHz/20181013%20-%20IMG_8245.jpg http://www.imagic.pl/files/2853/ …

Today I've been playing around changing thermal paste in PII CPU. Dissasembling that particular CPU which I own (SL2S5) was a nightmare. I couldn't easily pry plastic case in one corner, because one pin was keeping it so tightly that I've bended some part of plastic case and broken my plastic tool …

@oeuvre Don't worry. Computer is in case now. Like on photo is the best way for me to test something. I have access from every side to computer components. Now it's time for the best part. Playing with IRQ and DMA. Surprisingly win98se messed up with them. Radeon is on DMA 5, SB AWE32 on DMA 10, IRQ …

Forgive me post under post, but too long time passed since last one. Somethings changed today. I still had problems with this motherboard. Clean installation with only Radeon 7000 and SB AWE32. After 1 hour I gave up, but later I was still thinking and suspicions goes to RAM. I was using Kingston …

Chipset which You have there is 440ZX. FSB 66 or 100MHz. In Ami Bios 4 beeps are for System Timer Failure. If it beeps 1 long 3 short then: - Ami Bios gives "Conventional/Extended Memory Failure" - Award Bios gives "Keyboard Controller error" It's hard to say what error You may have without any PCI …

20180120 19:57 Bath is simple soap with water... Nothing special. I wanted to get rid of dust. And btw. I'm doing this with all other dirty parts so It's not a reason for that kind of behavior with Radeon 7000 and Direct3D... After reading some post here on vogons about some problems with radeon …

Ok. From what I see on attached photo, near battery is drawn table with CPU Bus Ratio. Check these settings with connector below battery (I think this is for setting CPU Bus Ratio). On right side of battery are switches for disabling/enabling internal GFX card. Above battery is table with …

Can You make other photos of this motherboard? From what I've found it has integrated graphic card Ati Rage 3D. Maybe You need to change settings in Bios to be able to use external Graphic Card...

I have problems with this small motherboard. My suspicions are for damaged AGP port. Firstly I was blaming ATI Radeon 7000. When I try to run any 3D game on Direct 3D. Game jumps out to Windows and close itself without any warnings. Under Voodoo II the same title runs normally. I've checked with …

Post updated.

Here I want to share some information about my Retro Rig based on Pentium II 333MHz on Gigabyte GA-6EM rev 1.8 motherboard. Firstly I've build PIII 600MHz with 256MB RAM and integrated Sound Card based on ESS Solo-1. Motherboard was Biostar M6TZF. It was a lot of fun to install Win'98SE and drivers. …

Just got my interest now. Too bad a little late 😉 I'm waiting for final interview to see or read it. Indeed a very interesting project.

I bought this board very cheap. I've received it with 16MB of RAM in 4x4MB 30-pin SIMM. It's the same as in this auction. Unfortunately it's without manual, cables or disk with utilities. I've tried to find some info on internet but without success. As far as I know this board have: - AMD 386SX 40 …

It's not entire "Sold Out" collection. I've wanted titles only for PIII 600 MHz & Win98 but I have couple more titles for better CPU.

This is my working space. A room is very small, so I must cut a space taken by my computers... Right monitor is a TV for main PC rig, second PC PIII 1.1GHz, C64, Amiga 600, PS2 Slim, other consoles/computers which I may buy. Left monitor is turned right by 90 degrees. It's easier to read books/ …