Re: I recently found this hardware, AKA the Dumpster find thread.

Posted on 2016-11-04, 06:09

by

by kaputnik

in Marvin \ General Old Hardware

in Marvin \ General Old Hardware

Went to recycle some electronics stuff at work (doing it myself instead of delegating it since I got bitten by the retro bug :D) and scored this gem: DSC_0604.JPG A Black Box SW622A-R2 4-port KVM switch. Its exterior was quite dirty, but otherwise it is as good as new. Found it with only two KVM …

---

Re: Socket 7 cpu with passive cooling

Posted on 2016-11-04, 04:02

by

by kaputnik

in Marvin \ General Old Hardware

in Marvin \ General Old Hardware

If there aren't lots of peripheral components protruding from the mobo close to the socket, you could always use a Socket 370/A heatsink with Socket 7. There are plenty of large and effective models around, that probably could handle the heat even from higher clocked Pentiums without a fan. If not, …

---

Re: DreamBlaster X1 : a rare card

Posted on 2016-10-30, 11:13

by

by kaputnik

in Marvin \ General Old Hardware

in Marvin \ General Old Hardware

Didn't even know this project existed until now. Looks like I'll have to pick up the X2 when released, assuming that the X2 sounds at least as good as the X1. And yes, a few grab bag samples from Duke3d and Doom would be really nice 😀 Edit: had to pick up an S1 while I wait 😁

---

Re: Gravis Ultrasound Classic problems

Posted on 2016-10-29, 20:55

by

by kaputnik

in Marvin \ General Old Hardware

in Marvin \ General Old Hardware

This dirt doesn't look like the usual dust. Maybe you should clean the board with water, soap and toothbrush. After that, dry at 100°C. Remove all socketed chips before doing so. I removed all the chips, including the big GF1 mofo. SOme of the pins (or contacts or whatever they are called) of that …

---

Re: What retro activity did you get up to today?

Posted on 2016-10-28, 21:48

by

by kaputnik

in Marvin \ General Old Hardware

in Marvin \ General Old Hardware

clueless1 wrote: Nice 😀 I didn't' see what cpu you are using, but that is such a cool setup. Makes it look like an industrial system. It's a Pentium 200, so it's possible to use all settings without overclocking. Thanks 😀

---

Re: What retro activity did you get up to today?

Posted on 2016-10-28, 21:33

by

by kaputnik

in Marvin \ General Old Hardware

in Marvin \ General Old Hardware

Was originally gonna replace the FSB frequency and multiplier dipswitches with pinheaders on my Gigabyte GA-586HX board, to be able to connect external FSB/multiplier switches, but turned out there are revisions of the same board where you set those with jumpers. The jumper headers were there on my …

---

Re: A3D 2.0 and EAX cards together in one machine?

Posted on 2016-10-27, 23:48

by

by kaputnik

in Marvin \ General Old Hardware

in Marvin \ General Old Hardware

Sorry for late replies, some bad mojo popped up in my life. Posting from my phone, PCs are packed away currently. The CS4630 was stated to have full acceleration, and the CS4624 was stated to have partial acceleration, not entirely sure what is and isn't. Sensaura sounds really good, but A3D 2.0 is …

---

Re: Are Geforce 256s rare or hard to find?

Posted on 2016-10-27, 11:37

by

by kaputnik

in Marvin \ General Old Hardware

in Marvin \ General Old Hardware

Why do you want a GF256 specifically? Is there anything it can do that a GF4 card can't? The latter is both easy to find and way more powerful. Replaced the GF256 in my PIII/W98 rig with a Ti4200 a while ago, haven't run into any problems so far anyways. Also, the GF4 series card are compatible with …

---

Re: Last parts for vintage gaming rig on their way!

Posted on 2016-10-24, 11:28

by

by kaputnik

in Marvin \ System Specs

in Marvin \ System Specs

Oh, jeez... Yeah. I see it now. My bad. :facepalm: Hehe, shit happens :) Would be great if you could do some compatibility tests once you got it all up and running, interesting to see how the P3C compares to 440BX boards in that respect. May I ask what you paid for the board aswell? Never even seen …

---

Re: Last parts for vintage gaming rig on their way!

Posted on 2016-10-23, 21:55

by

by kaputnik

in Marvin \ System Specs

in Marvin \ System Specs

On a related note, you've made a small typo in the OP. P3B-L should be P3C-L :) Ah, you are correct. It's confusing, because the version with LAN, SCSI, or both, is the P3C (-L, -S, or -LS,) where the version with neither is the P3B... The P3B is the exact same physical board, just guaranteed …

---

Re: A3D 2.0 and EAX cards together in one machine?

Posted on 2016-10-23, 15:29

by

by kaputnik

in Marvin \ General Old Hardware

in Marvin \ General Old Hardware

Very interesting read! Got a Santa Cruz with the Crystal CS4630-CM EP chip, that I thought was kind of useless for retro purposes. Got it when a friend called to tell me he had found three soundcards that looked really old in a thrift store, and asked if I wanted him to pick any of them up for me. …

---

Re: Last parts for vintage gaming rig on their way!

Posted on 2016-10-22, 18:04

by

by kaputnik

in Marvin \ System Specs

in Marvin \ System Specs

Absolutely awesome system, would probably put together something like it if I decide to build the retro rig of my dreams without a budget at some point. The mobo alone is worth killing for 😁 On a related note, you've made a small typo in the OP. P3B-L should be P3C-L 😀

---

Re: What retro activity did you get up to today?

Posted on 2016-10-17, 13:48

by

by kaputnik

in Marvin \ General Old Hardware

in Marvin \ General Old Hardware

Pin modded a SPC370 slotket to accommodate for Tualatin CPU:s. Might be easier to do parts of the mod on the the CPU instead, but slotkets are kind of cheap, and doing it all on the slotket makes future CPU swapping easier, as you just have to fit the new CPU without insulating any pins on it. …

---

Re: Questions about P3 Tua vs Athlon XP

Posted on 2016-10-17, 09:27

by

by kaputnik

in Marvin \ General Old Hardware

in Marvin \ General Old Hardware

Running an XP 2400+ on a KT133A board together with a Ti4600. Using the 45.23 Detonator drivers and 4.42 VIA 4-in-1 chipset drivers. Never gave me any trouble whatsoever, except for having to recap the mobo. In fact, it feels even more stable and robust than my 440BX system. Works just as good in …

---

Re: craiglist deal Really old computer and monitor

Posted on 2016-10-14, 07:28

by

by kaputnik

in Marvin \ General Old Hardware

in Marvin \ General Old Hardware

syndicator wrote: I am still going to buy that XT system as soon as i get my car back from my mother and i will update you guys on the 8088 system.. Do it. Worst case scenario, if the computer itself doesn't work, is that you get a completely awesome case 😀

---

Re: Having trouble sorting out what options there are in the top of the line for a Win98 100FSB system in ATX or EATX

Posted on 2016-10-11, 21:57

by

by kaputnik

in Marvin \ General Old Hardware

in Marvin \ General Old Hardware

I'd go Athlon 1400B KT133 That would be the fastest build, it also gets you ATA100 if you get the 636B chipset, more than 2 USB ports, 1-3 ISA slots (my AZ11E has 2 ISA slots), AGP 4X so you can run from AGP 1x to AGP 8x cards, support from 512mb High Density SD-Ram Also by Socket A, VIA had very …

---

Re: Having trouble sorting out what options there are in the top of the line for a Win98 100FSB system in ATX or EATX

Posted on 2016-10-11, 16:56

by

by kaputnik

in Marvin \ General Old Hardware

in Marvin \ General Old Hardware

I'd go Athlon 1400B KT133 That would be the fastest build, it also gets you ATA100 if you get the 636B chipset, more than 2 USB ports, 1-3 ISA slots (my AZ11E has 2 ISA slots), AGP 4X so you can run from AGP 1x to AGP 8x cards, support from 512mb High Density SD-Ram Also by Socket A, VIA had very …

---

Re: DOS 7.1 will only partition 8GB CF card

Posted on 2016-10-11, 11:24

by

by kaputnik

in Marvin \ General Old Hardware

in Marvin \ General Old Hardware

Well, even in the 486 it's listed as CF CARD and ~32000 mb. The FreeDos FDISK also reports only 8GB total space. It works at 8GB, almost. It gets general read errors randomly and it basically is a waste of a purchase. Is there any place that lists decent brands and types that are known to work in …

---

Re: DOS 7.1 will only partition 8GB CF card

Posted on 2016-10-11, 11:14

by

by kaputnik

in Marvin \ General Old Hardware

in Marvin \ General Old Hardware

Are you sure it detects as a 32GB card in BIOS? Got a 16 GB Kingston 266x card that won't detect as more than 8 GB, sometimes only as 4GB, in three different computers with two different BIOS manufacturers. It seems to live its own life, there's no consistency at all. It's working perfectly in USB …

---

Re: Having trouble sorting out what options there are in the top of the line for a Win98 100FSB system in ATX or EATX

Posted on 2016-10-11, 09:28

by

by kaputnik

in Marvin \ General Old Hardware

in Marvin \ General Old Hardware

It's not a Slot 2 system, but would say my 440BX build falls in that category as far as 100 MHz FSB systems goes, clicky . Scroll down a bit, it's in the bottom of the OP. Might give you some ideas :) Have a look at the DOS/W98 monster too, it's about as powerful it gets if you want ISA without …

---