VOGONS

Search

Common searches

Search results

Display options

Display options

Re: VGA Capture Thread

Posted on 2021-03-17, 18:34

Ok, so here's a first pass: VGA Out (Riva TNT2 Ultra to 2 x Diamond Monster 3D II in SLI) to VGA Splitter to OSSC 1.6 (Passthrough) HDMI Out to HDMI-to-DVI Adapter to DataPath VisionRGB 1S. Captured using OBS at native 1280x1024 (Windows 98SE), and launched GLQuake @ 1024x768. Went in and out back …

Re: VGA Capture Thread

Posted on 2021-03-16, 17:47

Thanks for your responses! So I picked up this beauty for about $114.00, installing it in my main capture box (replacing my Elgato 4K CamLink). So for this card seems to hold it's sync when switching refresh rates/resolutions. Now I just gotta figure out the audio capture piece since I completely …

Re: VGA Capture Thread

Posted on 2021-03-16, 16:57

Thanks for your responses! So I picked up this beauty for about $114.00, installing it in my main capture box (replacing my Elgato 4K CamLink). So for this card seems to hold it's sync when switching refresh rates/resolutions. Now I just gotta figure out the audio capture piece since I completely …

Re: VGA Capture Thread

Posted on 2021-03-13, 00:22

So I've read this entire thread - wowza, lots of good info and much more complex than anticipated. I've bought (and returned) quite a few items (thank you Amazon) as I didn't read this thread first before buying and honestly thought video capture would have come a long way by now. However, capturing …

Re: Cable / Connector Identification Needed

Posted on 2021-02-09, 00:45

in Milliways
I think this is what I need? https://www.ebay.com/itm/JST-PH-2-0mm-Pitch-4Pin-Female-Connector-Crimp-Contact-Pin-Header-Connector-x-20/184573956720?epid=833499484&hash=item2af9771270:g:KMYAAOSwxphbHzHK definitely looks like it. Origin hong kong, could take a while for delivery. Done and Done. With …

Re: Cable / Connector Identification Needed

Posted on 2021-02-08, 21:02

in Milliways
And I always make sure to buy excess pins since I often mess a few of them up, especially for connectors I am unfamiliar with. Lots of trial and error! So I've learned! :) I think I'm just going to try to source a bunch of the male version of the JST-PH 4-pin 2mm connectors and try my luck. I just …

Re: Cable / Connector Identification Needed

Posted on 2021-02-08, 17:46

in Milliways
I have never crimped AMP connectors myself, but an easier route would probably to take a premade computer cable with the right connector and thinner cables and just crimp the JST-PH connector onto that... that crimping tool looks pretty bad imho, and not like it has the correct jaws, they need to …

Re: Cable / Connector Identification Needed

Posted on 2021-02-08, 17:43

in Milliways
Well, you made me curious and... from the wikipedia... https://en.wikipedia.org/wiki/Molex_connector There are three typical pin sizes: 1.57 mm (0.062 in), 2.13 mm (0.084 in), and 2.36 mm (0.093 in). Guess which ones a pc uses... it's the middle one. I pulled one out of a connector, measured it and …

Re: Cable / Connector Identification Needed

Posted on 2021-02-08, 15:57

in Milliways
Both are definitely options as I cannot seem to find this cable myself (was hoping for the easy way). I did pick up a molex crimping tool but I do have some questions as I haven't had much success, instead just destroying some pins as I'm a novice. This is the crimping tool I bought: https://www. …

Cable / Connector Identification Needed

Posted on 2021-02-07, 20:33

in Milliways
Hey all- This cable recently snapped off my mining rig and was used to power the front LCD display. Any idea what type of connector the little one is? Unfortunately I reached out to several eBay sellers who are selling the same open air rig, but they do not offer the cable or front panel separately. …

Page 3 of 90

Go to top of page Go to top of page
Close window
Close window