I have measured the traces on the left (in the detailed Picture) arround U6. I have not yet (will do on Friday) meassured the traces arround U20. When saying meassured i mean following the possible faulty traces from one end to the other end using the PCB diagram. The reason that i belive the …

I checked all the solderings tonight (with the help of my friend Francis) No problems where the solderings looks bad. According to Commodore 128 trouble shooting guide i have decied to replace the ROCKWELL R65C22P2 DIP-40 Versatile Interface Adapter (VIA) 16 I/O. I orderes two on eBay just know - …

This is what i have done so far. 1. Dismantle and wash all components, except power supply - in dishwasher. 35 degrees Celsius. No soap 2. Connect and try. All works except Internal Floppy Drive: 1571D - I have not found a manual for the 1571D yet. 3. Damaged tracks on the PCB card for the Floppy …

I have and original (first gen) 128D Pal, that needs repair. It workes (as far as i can tell) without the internal Floppy Drive connected. This leads me to beleive that the floppy driver or the floppy controller is the problem. External Floppy connected to the serial port workes fine - when the …

Unfortunately, it will not work without a modded BIOS. The default BIOS on Toshiba portables from that era will only accept IDE hard drives that identify themselves as a Conner "CP" model drive, and even then only two or three specific capacities. You can't just slap in any old non-Conner branded …

Anybody has any experience with using a Compact Flash as HDD on an Toshiba T5200 (or similar). This is a 386 machine with a IDE hdd.

Yep, http://www.vcfed.org/forum/showthread.php?26393-XTIDE-project If you're feeing lucky, it even lets you emulate a hard drive using an XP box or a Raspberry Pi . This project is bases on the ISA bus. What about using the External HDD connector on an old PC/XT? Would it work if i made a cable and …

Has anybody tried to use a IDE to CF interface, or a Disk on Memory (DOM) with the Schneider Euro PC? - Or with any old 8088 pc?

The trace is fixed. The computer now boot from a floppy ! But.. The Spacebar, Ctrl, Alt, Q and a few other keys to the left side of the keyboard is not working.... Ideas? I opened the keyboard and found that i have connection between red dots, but somewhere along the path (yellow) to the pink spot i …

I found the error, or maybe i should say that keenerb found the error. keenerb's first suggestion was correct. The trace was partly gone. See picture. When i manually short circuit (see picture) the floppy startet to load from disk... How do i fix the trace? This is extremely small. Any good …

It does not boot from floppy. The floppy motor starts but it is unable to boot. I don't think the keyboard is faulty. I have opened it and it looks fine.

I have an Schneider Euro PC that does not start up. It beep 13 times, and show these error message. I have changed the battery (after the photo was taken). As you can see on the photo there are some damaged from the previous leaked battery. I am not able to enter BIOS Setup by pressing CTRL-ALT-ESC. …

When the Gonbes specs say it supports "CGA", they actually mean 15kHz analogue video. PC CGA is 15kHz digital video, hence the need for a digital to analogue converter like the one linked and the circuits posted elsewhere. Thanks for Your answer But what about the BIT-C-128? It is called a DAC si i …

bjt wrote: This is the only place I know of selling them ready-made. This should display brown correctly too. http://bit-c64.com/ Why do i need the BIT-C-128? The Gonbes GBS-8200 says is supports CGA input? Also: Could the BIT-C-128 bu connected to a SCART connector?

I want to make or buy a CGA (RGBi) to SCART to use on my Schneider Euro PC. Anybody that sell these? If Not where can i buy the components needed? Any kit available?