It takes regular video ram chips - like what's socketed on most PCI cards: AT3Ds.JPG If you have any video card with socketed chips like the ones above, you can remove them and place them in the sockets for the on board cirrus logic. Just make sure not to put them in backwards - the dot on the side …

kanecvr wrote: I bet the on-board video card being enabled is the reason for your troubles. BTW, what is the on board video card? If it's a cirrus logic it's just as good as the S3 Trio64 (especially the CL-GD54xx versions). yes its exactly this same version 😁

yes its a cirrus logic....it seem to be able for upgrades...i see two empty slots... what kind of chips goes in there ? I wanted to go for a Dos menu system.. i always liked Direct access back when i was a kid. sadly cirrus logic doesnt like it :/ (resolution problems..if i try to change screen... …

Erm, what about J3? Did you tried it? Ok tryed to put a jumper on J3. didnt change anything. its still wont even go 640x480 on 256 color...im stuck at 16 colors. Hmm... That's indeed a strange issue you've got. Never had serious problems with a Trio myself so far. If it is similar to the card in …

elianda wrote: Erm, what about J3? Did you tried it? nope, didnt find anything related to those. i will try setting one on j3 tonight and write back about it

Go into BIOS and set " Assign IRQ to VGA " and " PCI VGA Palette Snoop " to " Enabled " There's no such option in my bios..does that mean i should figure out a way to update it ? It might as well be that the card has a jumper to enable VGA IRQ, which should be set. here's the card i got, except for …

Card is a S3 Trio64V2/DX 2 MB RAM PCI VIDEO CARD i have 64mb of ram on current PC im using for this.

I manage to get everything working at last.... (except that damn x3 problem for the amd5x86) and this is the very last problem (i hope) i seem to get. After installing a S3 trio64/v2 i noticed that it wont go higher then very low resolution. -trying to play duke nukem 3d in svga cause game to not …

Hmm.. jumper sets -66mhz -------------------------J1A1-A2 pins 1-2 closed -SL-Enhanced -----------------J5A2 pins 1-2 closed -non-SX ------------------------J5A3 pins 1-2 closed -Pentium overdrive disable -J4A2 pins 1-2 closed -3.3 volts ----------------------J1A1-A2 & J2A1-A2 - pins 1-2 closed and …

so SX/DX jumper should be put on DX ? because if you look at the URL i put up there. looking around the jumpers... i didnt see anywhere where to put it it at 2x.. unless its the DX option

Hi i finally found some help regarding my motherboard's manual i can at last install the AMD 5x86 P75 you can see it here : http://stason.org/TULARC/pc/motherboards/I/INTEL-CORPORATION-486-CLASSIC-PCI-LPX.html now, using Chkcpu i looked if my current setup can manage to get it to run at 133mhz but …

i put back the cpu it came in with. i think i found some infos, http://www.elhvb.com/mobokive/Archive/Intel/Classic-PCI-ED_4317.pdf i got the almost exact same jumpers. At least it can give me some help. if i remember 5x86-133 jumpers needs to be on 3.3v ? i didnt put them there so that might be the …

Hi :) very interesting forum. I've read some post up to now for some help but lately i'm having problems. I just found an old 486 system. I started to mess around with it but... i can't find any infos about that damn motherboard. only place i saw something about that mobo was from some russian …