VOGONS


First post, by elianda

User metadata
Rank l33t
Rank
l33t

I recently got a Matrox Impression Lite with 2 MB as PCI card using a IS-ATHENA R2 chip from 1995 and a seperated CL-PX2085 DAC. The card has a EEPROM BIOS.

I first tried with Win98SE which brings already a driver for it. There was nothing really special about it.
Then I tried the Win95 driver which brings Powerdesk and some tools, but also nothing real special. 2D-Performance was in both cases good.

I noticed that in DOS there is no VESA support from BIOS at all.
320x200 at 256 colors is utterly slow, with about 12 fps in Duke3D and vidspeed reported a performance of an old 8 bit ISA VGA card. (about 8 times slower than a ISA TSENG ET4000).
I looked for a VESA driver and found one in the Windows 3.x software.
It supports VESA 1.2 and enables up to 1024x768 at 256 colors interlaced.
So I tried Duke3D again at 640x480 and 800x600 which gives 1-2 fps, you can watch the screen repainting. Same applies for Descent2...
Then there is some ominous setvga tool which has a -m1 and -m2 parameter and is no TSR, just changes some hardware setting.
So -m2 increased the 320x200 mode performance to 22 fps in Duke3D which is ok. VESA mode performance did not increase.
The speed difference between Windows and DOS is astonishing.
(kind of DOS gaming protection for CAD engineers 😉 ).

I also found a board information tool for Win 3.x and it works also in Win 9x:

So what about this 3D Wireframe Acceleration?

I looked into some readmes and there is a 3D Screensaver mentioned on the Supplemental Disk. After further search I found it there
ftp://ftp.matrox.com/pub/mga/othermga/previous/15512220.zip

The disk also includes a VfW 1.1d DCI driver and a Dynaview3D Application for AutoCAD12 and 13 models. The Screensaver needs a AutoCAD model to show. Now it looks that this API is only available from Windows 3.x since Dynaview3D can not load a required sxci library.
Also the Screensaver just shows a 2D Matrox logo and it does not matter which 3D model I choose.

So next time I try with this card I should go for a Win 3.x setup.

Last edited by elianda on 2014-01-11, 00:10. Edited 1 time in total.

Retronn.de - Vintage Hardware Gallery, Drivers, Guides, Videos. Now with file search
Youtube Channel
FTP Server - Driver Archive and more
DVI2PCIe alignment and 2D image quality measurement tool

Reply 1 of 8, by Davros

User metadata
Rank l33t
Rank
l33t

for dos maybe univbe would help

Guardian of the Sacred Five Terabyte's of Gaming Goodness

Reply 2 of 8, by elianda

User metadata
Rank l33t
Rank
l33t

Well, I forgot to mention it, that I also tried UniVBE and it detects it as 037 Oti with 256kB and 8 Bit DAC, so obviously wrong.

Retronn.de - Vintage Hardware Gallery, Drivers, Guides, Videos. Now with file search
Youtube Channel
FTP Server - Driver Archive and more
DVI2PCIe alignment and 2D image quality measurement tool

Reply 3 of 8, by Mau1wurf1977

User metadata
Rank l33t++
Rank
l33t++

Could be a good slow-down card for fast machines?

Reply 4 of 8, by Putas

User metadata
Rank Oldbie
Rank
Oldbie
elianda wrote:

So what about this 3D Wireframe Acceleration?

ATHENA R2 was first "home" 3d acceleration chip, but it cannot do texture mapping. Same 3d engine was in first Millennium. Few games with Goraud shaded polygon graphics were bundled. Can you check with dxdiag if Direct3d acceleration is enabled?

Reply 5 of 8, by elianda

User metadata
Rank l33t
Rank
l33t

I think it was not. The screenshot above states also ddraw 1.0 capabilities for the driver and D3D was introduced with DX3.

Retronn.de - Vintage Hardware Gallery, Drivers, Guides, Videos. Now with file search
Youtube Channel
FTP Server - Driver Archive and more
DVI2PCIe alignment and 2D image quality measurement tool

Reply 6 of 8, by vlask

User metadata
Rank Member
Rank
Member

If you wanna have some fun, then try patched Turok demo. It works (think i tested it on Millenium card) in 3d mode, but without textures it look really strange.... 😈

Not only mine graphics cards collection at http://www.vgamuseum.info

Reply 7 of 8, by Gona

User metadata
Rank Member
Rank
Member
elianda wrote:

Well, I forgot to mention it, that I also tried UniVBE and it detects it as 037 Oti with 256kB and 8 Bit DAC, so obviously wrong.

It seems IS-ATHENA chips supported by UniVBE from version 5.2

Somebody have the bundled CD of the Matrox Impression card?

Video card compatibility matrix for DOS games | ATI3DCIF compatibility matrix | CGL API compatibility matrix

Reply 8 of 8, by Gona

User metadata
Rank Member
Rank
Member

vetz has succesfully tested the "Renderware API" on his Matrox Impression Plus card:
It seems this Renderware API works only on Matrox Athena chip based cards.
Re: 3D Accelerated Games List (Proprietary APIs - No 3DFX/Direct3D)

Video card compatibility matrix for DOS games | ATI3DCIF compatibility matrix | CGL API compatibility matrix