CMOS battery replacement question (Packard Bell 386SX-II motherboard) \ VOGONS

CMOS battery replacement question (Packard Bell 386SX-II motherboard)

Topic actions

Post a reply

First post, by Geforcefly

Posted on 2021-01-20, 04:32

Geforcefly Offline

Rank Newbie

Rank: Newbie
Posts: 18
Joined: 2018-01-02, 04:23

I've been reading up on various CMOS battery replacements, but I have a question: The board I'm working on had a 3.6v barrel battery that I removed before any damage could be done. There is an external battery connector that measures 5 volts when the power is on. Based on that, I would think that I'd need to use a 4AA battery holder with rechargeable batteries for safe operation (without modification). There are diodes around the area (shown in the attached picture), so perhaps maybe? Let me know what you think.

Attachments

Filename

PXL_20210120_042023447.NIGHT.jpg

File size

64.98 KiB

Views

459 views

File comment

386SX-II battery area

File license

Public domain

Reply 1 of 10, by Thermalwrong

Posted on 2021-01-20, 09:19

Thermalwrong Offline

Rank Oldbie

Rank: Oldbie
Posts: 1432
Joined: 2018-03-18, 19:24
Location: England

I've got the same board I think, I just put a coin cell on the terminals like this. It seems to work, but if you're seeing 5v on there, I wonder how safe it is?

Attachments

Filename

IMG_0765 (Custom).jpeg

File size

729.29 KiB

Views

447 views

File license

CC-BY-4.0

Reply 2 of 10, by maxtherabbit

Posted on 2021-01-20, 14:59

maxtherabbit Offline

Rank l33t

Rank: l33t
Posts: 3359
Joined: 2018-10-30, 16:36
Location: Richmond, VA

Normal to see 5v on the ext battery header. It doesnt mean anything - there is a diode (or 2) protecting the battery from being charged by it

Reply 3 of 10, by douglar

Posted on 2021-01-20, 15:45

douglar Offline

Rank Oldbie

Rank: Oldbie
Posts: 1370
Joined: 2019-11-04, 15:37

I did my first battery replacement yesterday, also with a 386sx.

Filename

Photo Jan 20, 10 38 44 AM.jpg

File size

39.07 KiB

Views

422 views

File license

Public domain

I soldered the minus pin to the motherboard and bridged one of the plus pins to the motherboard with a diode.
I used a little hot glue to stabilize the coin socket.
Diode caused the voltage to drop from 3.3V to 3.05v, but the motherboard seems to be OK with that.

Did I do that right?

Reply 4 of 10, by chrismeyer6

Posted on 2021-01-20, 16:05

chrismeyer6 Offline

Rank l33t

Rank: l33t
Posts: 2702
Joined: 2015-10-13, 16:16
Location: NJ, USA

As long as the battery isn't getting the charging voltage and your bios settings are being stored you should be good to go. I'd also make sure to clean off more of that corrosion as it will continue to eat away at your motherboard.

Reply 5 of 10, by douglar

Posted on 2021-01-20, 17:06

douglar Offline

Rank Oldbie

Rank: Oldbie
Posts: 1370
Joined: 2019-11-04, 15:37

chrismeyer6 wrote on 2021-01-20, 16:05:

I'd also make sure to clean off more of that corrosion as it will continue to eat away at your motherboard.

I gave it a third scrubbing with vinegar and none of the green would come off on the swab. Should I try a different solvent?

Reply 6 of 10, by chrismeyer6

Posted on 2021-01-20, 18:01

chrismeyer6 Offline

Rank l33t

Rank: l33t
Posts: 2702
Joined: 2015-10-13, 16:16
Location: NJ, USA

You can try some 99% isopropyl alcohol and a soft tooth brush and see if you can get anymore off and then give it a quick rinse with some distilled water

Reply 7 of 10, by douglar

Posted on 2021-01-20, 20:14

douglar Offline

Rank Oldbie

Rank: Oldbie
Posts: 1370
Joined: 2019-11-04, 15:37

chrismeyer6 wrote on 2021-01-20, 18:01:

You can try some 99% isopropyl alcohol and a soft tooth brush and see if you can get anymore off and then give it a quick rinse with some distilled water

That didn't make a dent in it either. I ended up using some "lime-a-way" cleaner that I use on hard water stains. That took off the deposits after a little scrubbing. I rinsed it well afterwards.

Reply 8 of 10, by chrismeyer6

Posted on 2021-01-20, 20:40

chrismeyer6 Offline

Rank l33t

Rank: l33t
Posts: 2702
Joined: 2015-10-13, 16:16
Location: NJ, USA

Good I'm glad you found something that was able to work for you. Getting it as clean as possible allows for a nice long life for your parts.

Reply 9 of 10, by Geforcefly

Posted on 2021-01-21, 03:38

Geforcefly Offline

Rank Newbie

Rank: Newbie
Posts: 18
Joined: 2018-01-02, 04:23

Thanks for the feedback. I'll probably get a 3xAA battery holder and place it away from the board to eliminate any chance of battery corrosion causing issues.

Reply 10 of 10, by chrismeyer6

Posted on 2021-01-21, 03:56

chrismeyer6 Offline

Rank l33t

Rank: l33t
Posts: 2702
Joined: 2015-10-13, 16:16
Location: NJ, USA

That's a good idea keep the batteries as far from the other components as possible.

Go to top of page Go to top of page

Back to General Old Hardware

Main menu

Common searches