Tried this GPU, but I got 1 Long beep + 3 short beeps :[ Yeah, I know that it's about GPU detection. Is it possible to investigate further? AGP port incompatibility maybe?
Does the card work in any computer ?
Other members with ATI 9800XT boot issues: P3V4X and 9600XT issue
Hate posting a reply and then have to edit it because it made no sense 😁 First computer was an IBM 3270 workstation with CGA monitor. Stuff: https://archive.org/details/@horun
Thats odd all the 9600 series cards I have seen are keyed to 1.5 volts only.
{edit} See here: http://www.playtool.com/pages/agpcompat/agp.h … sal15vagp30card
Yeah nearly all the Google images show a 1.5v only slot, plus since you mentioned it: it does not have the full compliment of onboard parts, many missing Caps,VRegs and others compared to most (many spaces empty compared to VGA Museum)
Hate posting a reply and then have to edit it because it made no sense 😁 First computer was an IBM 3270 workstation with CGA monitor. Stuff: https://archive.org/details/@horun
It is very likely due to a bus frequency issue between the agp and cpu.
(see page 15)
https://dlcdnets.asus.com/pub/ASUS/mb/slot1/4 … -f/p2bf-103.pdf
I encountered a similar problem with a 9800xt and an MSI socket A board which I ended up replacing with a 6800gt
GinnunGagap wrote on 2023-03-07, 21:51:AGP port incompatibility maybe?
as written above, the 9600 is a 1.5V only card (AGP 4x/8x). BX - 3.3V - AGP 1.0 (2x).
If you're lucky, the video card may be alive.
Aopen MX3S, PIII-S Tualatin 1133, Radeon 9800Pro@XT BIOS, Diamond monster sound MX300
JetWay K8T8AS, Athlon DH-E6 3000+, Radeon HD2600Pro AGP, Audigy 2 Value
Makavre wrote on 2023-03-08, 03:12:I encountered a similar problem with a 9800xt and an MSI socket A board which I ended up replacing with a 6800gt
9800 - power hungry card, with powering GPU from 5V and ... 3.3V (two-phase operation whith current sharing control).
Works normally only with native ATX MB, not on combined AT/ATX boards.
Like CUBx-E, but not CUbX
Aopen MX3S, PIII-S Tualatin 1133, Radeon 9800Pro@XT BIOS, Diamond monster sound MX300
JetWay K8T8AS, Athlon DH-E6 3000+, Radeon HD2600Pro AGP, Audigy 2 Value
shevalier wrote on 2023-03-08, 05:36:as written above, the 9600 is a 1.5V only card (AGP 4x/8x). BX - 3.3V - AGP 1.0 (2x).
If you're lucky, the video card may be alive.
Technically, 9600 is not AGP 1.5v only card and can work with 3.3v signal, just like any other R3xx chip. Original ATi design just didn't bother with compatibility, avoiding a lot of angry customers with AT boards and horrible early AGP chipsets, which still were somewhat common. But some third-party designs with external power connection (just like on GeForce FX ultra cards) will work fine.
When you combine 9600XT with such poor cost cut-down PCB without external power - problems are bound to happen.
I must be some kind of standard: the anonymous gangbanger of the 21st century.
Thanks! 😀
As stated above that's a bad implementation of that gpu . Try to run on it on a full atx motherboard and a old type 'beefy' 3.3/5v psu.
