VOGONS


Display options for a PC-XT

Topic actions

First post, by Anaxagoras

User metadata
Rank Member
Rank
Member

Hi guys!

I guess my CGA monitor is close to dead 🙁 and I have a VGA monitor and an old CRT TV.
I think that I can connect my PC-XT to any of them with the appropriate adapter or card but I don't know which.
Some years ago I had installed a Hercules card with monochrome video out but I lost it.

What of this ways is the best?
- Use the current CGA card --> External converter --> VGA monitor (TFT).
- Use the current CGA card --> External converter --> TV (CRT).
- Replace the current CGA for other CGA card with video out --> TV (CRT).

Maybe exists other options that I miss.

Can anyone address me with this?

Thanks a lot!

Last edited by Anaxagoras on 2026-11-17, 19:39. Edited 1 time in total.

My computers

Reply 1 of 25, by Babasha

User metadata
Rank Oldbie
Rank
Oldbie

ISA8 VGA videocard --> VGA monitor ???

Need help? Begin with photo and model of your hardware 😉

Reply 3 of 25, by Babasha

User metadata
Rank Oldbie
Rank
Oldbie
Anaxagoras wrote on 2026-11-17, 18:48:
Babasha wrote on 2026-11-17, 12:46:

ISA8 VGA videocard --> VGA monitor ???

Thanks Babasha, do you know if VGA card is compatible with CGA games?

I use ISA8 Oak OTI-037 videocard in my XT-based rig and never get any incompatibility now... and in early 90 too)))

Need help? Begin with photo and model of your hardware 😉

Reply 4 of 25, by Jo22

User metadata
Rank l33t++
Rank
l33t++

There are mode utilities that can put early ISA VGA cards into CGA or Hercules emulation modes.
Can be found here: Re: Realtek realtalk, is it the best VGA for CGA? What is?

"Time, it seems, doesn't flow. For some it's fast, for some it's slow.
In what to one race is no time at all, another race can rise and fall..." - The Minstrel

//My video channel//

Reply 5 of 25, by zyga64

User metadata
Rank Oldbie
Rank
Oldbie

I can recommend the Trident TVGA9000C card (*). It offers very good compatibility with CGA—and even better compatibility when using the utility program provided by Trident (which can also switch the card into Hercules mode).

(*) 16bit card jumpered to 8bit mode. My card additionally need some rework - ALE signal needs to be disconnected from the ISA ALE signal, and connected to the 5V power signal. As described in Sergey Kiselev's card design (bottom of the page): https://github.com/skiselev/isa-super-vga

8088@8 /640k /TVGA9000C /ALS100+TNDY 3voice
286@20 /4M /CL-GD5422 /CMI8330
486DX33 /16M /TGUI9440 /GUS+ALS100+MT32PI
K6-2@400 /64M /MGA-2064W+3dfx /YMF718
P!!!750 /256M /MX440 /Vibra16s+SBLive!

Reply 6 of 25, by Anaxagoras

User metadata
Rank Member
Rank
Member
Babasha wrote on 2026-11-17, 20:01:
Anaxagoras wrote on 2026-11-17, 18:48:
Babasha wrote on 2026-11-17, 12:46:

ISA8 VGA videocard --> VGA monitor ???

Thanks Babasha, do you know if VGA card is compatible with CGA games?

I use ISA8 Oak OTI-037 videocard in my XT-based rig and never get any incompatibility now... and in early 90 too)))

Thank you for share your experience 😀
After a quick search on eBay I only found 16 bits ISA cards. I remember having a 16-bit ISA card that worked in an 8-bit ISA slot. Is the same with this?

Jo22 wrote on 2026-11-17, 20:08:

There are mode utilities that can put early ISA VGA cards into CGA or Hercules emulation modes.
Can be found here: Re: Realtek realtalk, is it the best VGA for CGA? What is?

Thank you Jo22. As far as I can saw, to select the emulation mode a program.EXE is needed but, PC-XT only can execute COM files. I'm not quite sure if those cards works in PC-XT 😒

zyga64 wrote on 2026-11-17, 20:23:

I can recommend the Trident TVGA9000C card (*). It offers very good compatibility with CGA—and even better compatibility when using the utility program provided by Trident (which can also switch the card into Hercules mode).

(*) 16bit card jumpered to 8bit mode. My card additionally need some rework - ALE signal needs to be disconnected from the ISA ALE signal, and connected to the 5V power signal. As described in Sergey Kiselev's card design (bottom of the page): https://github.com/skiselev/isa-super-vga

Great! It seems that Sergey Kiselev's card Version 1.1 should work in PC-XT. Where can I order one?
For the other hand, what is the difference between TVGA9000C and TVGA9000I? Can these cards work in PC-XT even if they are 16-bit?

My apologies if I ask to much.

My computers

Reply 7 of 25, by theelf

User metadata
Rank Oldbie
Rank
Oldbie

A cheap trident 9000 are 8bit compatible and have Hercules/CGA/EGA support in any cheap CRT screeen

A win win cheap 100% compatible and fast as hell for a XT

Reply 8 of 25, by wierd_w

User metadata
Rank l33t
Rank
l33t

In addition to 8bit oak vga, one could use early trident tvga cards, and might *try* 8bit serdavision video.

Reply 9 of 25, by BitWrangler

User metadata
Rank l33t++
Rank
l33t++

Tridents are the easy option, but may not always have the jumper block installed that lets you strap it to 8 bit mode. So if you get lucky it's a simple jumper setting, if you don't, you might need to solder something on.

Unicorn herding operations are proceeding, but all the totes of hens teeth and barrels of rocking horse poop give them plenty of hiding spots.

Reply 10 of 25, by zyga64

User metadata
Rank Oldbie
Rank
Oldbie
Anaxagoras wrote on 2026-11-18, 14:32:

As far as I can saw, to select the emulation mode a program.EXE is needed but, PC-XT only can execute COM files.

That's not true. XT can execute EXE files as well (of course - why it shouldn't ?).

Anaxagoras wrote on 2026-11-18, 14:32:

For the other hand, what is the difference between TVGA9000C and TVGA9000I? Can these cards work in PC-XT even if they are 16-bit?

TVGA9000i is more integrated - it even has integrated RAMDAC (8 bit), whereas 9000C can be paired with true color DAC (not that this makes any difference when used with an XT or 286 system).
They both should work in 8bit slot: https://www.vgamuseum.info/index.php/cpu/item … ident-tvga9000i
Those cards linked above have jumper for selecting 8/16 bit mode.

8088@8 /640k /TVGA9000C /ALS100+TNDY 3voice
286@20 /4M /CL-GD5422 /CMI8330
486DX33 /16M /TGUI9440 /GUS+ALS100+MT32PI
K6-2@400 /64M /MGA-2064W+3dfx /YMF718
P!!!750 /256M /MX440 /Vibra16s+SBLive!

Reply 11 of 25, by Ozzuneoj

User metadata
Rank l33t
Rank
l33t

As others have mentioned, an OAK OTI-037 is a good option. I used one in my 5150 to hook it up to a VGA monitor. I think most of them allow you to jumper it for 8bit operation very easily.

It's also a good use for an Oak card like that because they are horribly slow for faster systems, but with a 4.77Mhz 8088 the video card is never going to be the bottleneck. 😀

Last edited by Ozzuneoj on 2026-11-18, 22:16. Edited 1 time in total.

Now for some blitting from the back buffer.

Reply 12 of 25, by Anaxagoras

User metadata
Rank Member
Rank
Member
zyga64 wrote on 2026-11-18, 20:10:
Anaxagoras wrote on 2026-11-18, 14:32:

As far as I can saw, to select the emulation mode a program.EXE is needed but, PC-XT only can execute COM files.

That's not true. XT can execute EXE files as well (of course - why it shouldn't ?).

You are right, I probably thought that because the software installed in my PC-XT is very old, from a time when EXE files didn’t yet exist.

zyga64 wrote on 2026-11-18, 20:10:
TVGA9000i is more integrated - it even has integrated RAMDAC (8 bit), whereas 9000C can be paired with true color DAC (not that […]
Show full quote
Anaxagoras wrote on 2026-11-18, 14:32:

For the other hand, what is the difference between TVGA9000C and TVGA9000I? Can these cards work in PC-XT even if they are 16-bit?

TVGA9000i is more integrated - it even has integrated RAMDAC (8 bit), whereas 9000C can be paired with true color DAC (not that this makes any difference when used with an XT or 286 system).
They both should work in 8bit slot: https://www.vgamuseum.info/index.php/cpu/item … ident-tvga9000i
Those cards linked above have jumper for selecting 8/16 bit mode.

I found several of these cards on eBay at reasonable price.

Thanks all for your help!

My computers

Reply 13 of 25, by rmay635703

User metadata
Rank l33t
Rank
l33t

Ibms CGA adapter works natively with a rca composite equipped screen which includes many TVs and commodore monitors.

3rd party CGA usually isn't tv compatible without more work

Reply 14 of 25, by Anaxagoras

User metadata
Rank Member
Rank
Member
rmay635703 wrote on Yesterday, 04:48:

Ibms CGA adapter works natively with a rca composite equipped screen which includes many TVs and commodore monitors.

3rd party CGA usually isn't tv compatible without more work

Thanks rmay635703, good to know. But It sounds very expensive, at least to me.

My computers

Reply 15 of 25, by Ozzuneoj

User metadata
Rank l33t
Rank
l33t
Anaxagoras wrote on Yesterday, 06:46:
rmay635703 wrote on Yesterday, 04:48:

Ibms CGA adapter works natively with a rca composite equipped screen which includes many TVs and commodore monitors.

3rd party CGA usually isn't tv compatible without more work

Thanks rmay635703, good to know. But It sounds very expensive, at least to me.

Sorry if I'm misunderstanding what you're saying, but he was just saying to use the IBM CGA card (Color Graphics Adapter) that many IBM PCs and XTs would have originally come with. Specifically, the card shown here (they will have either a green or brown PCB). The RCA jack on it is a basic composite video output, so you can connect it directly to any TV with a composite (yellow) video input.

An XT would normally have come with one of four IBM video cards... Either a CGA card, a Monochrome Display Adapter card, or less commonly an Enhanced Graphics Adapter card... or if someone was made out of money, a rare and stupidly expensive Professional Graphics Controller card.

If your system didn't come with a video card or didn't come with an IBM CGA card, then you're probably best off just getting an OAK or Trident card will connect to a VGA monitor unless you can find an IBM CGA card cheap. There are some interesting things you can do with the composite video out on a CGA card (video demos that do crazy things to output more colors), but that's a pretty specific use case.

Now for some blitting from the back buffer.

Reply 16 of 25, by Anaxagoras

User metadata
Rank Member
Rank
Member
Ozzuneoj wrote on Yesterday, 07:07:
Sorry if I'm misunderstanding what you're saying, but he was just saying to use the IBM CGA card (Color Graphics Adapter) that m […]
Show full quote
Anaxagoras wrote on Yesterday, 06:46:
rmay635703 wrote on Yesterday, 04:48:

Ibms CGA adapter works natively with a rca composite equipped screen which includes many TVs and commodore monitors.

3rd party CGA usually isn't tv compatible without more work

Thanks rmay635703, good to know. But It sounds very expensive, at least to me.

Sorry if I'm misunderstanding what you're saying, but he was just saying to use the IBM CGA card (Color Graphics Adapter) that many IBM PCs and XTs would have originally come with. Specifically, the card shown here (they will have either a green or brown PCB). The RCA jack on it is a basic composite video output, so you can connect it directly to any TV with a composite video (yellow) input.

An XT would normally have come with one of four IBM video cards... Either a CGA card, a Monochrome Display Adapter card, or less commonly an Enhanced Graphics Adapter card... or if someone was made out of money, a rare and stupidly expensive Professional Graphics Controller card.

If your system didn't come with a video card or didn't come with an IBM CGA card, then you're probably best off just getting an OAK or Trident card will connect to a VGA monitor unless you can find an IBM CGA card cheap. There are some interesting things you can do with the composite video out on a CGA card (video demos that do crazy things to output more colors), but that's a pretty specific use case.

Yes, I’ve understood. The original CGA card has an RCA video output. But I think that model – the CGA installed in the original IBM PC-XT – is more expensive than the Trident 9000 VGA and probably hard to find too.

Of course, I know that there are different things.
The problem, or my scenario, is the following:
- PC-XT clone with CGA adapter.
- Monochrome monitor (12'') that’s about to stop working (used in my current setup).
- TV (14").
- TFT (17'').

To be honest, I don’t know what the best setup is for using my PC-XT without spending too much money.
I think the Trident 9000 graphics card plus a TFT monitor is a cheap option, but it means sacrificing the original look and feel.
Of course, the best thing would be to replace the current monitor with a ‘new’ one, but it’s very difficult to find one in good condition, it’s too heavy to post, and I don’t know how long I’ll be able to use it for.

For the other hand the original CGA card with video output to use in TV is the best option in terms of look and feel.

At the moment I created two searches on eBay, one for Trident card and other for CGA with video output.

My computers

Reply 17 of 25, by Boohyaka

User metadata
Rank Oldbie
Rank
Oldbie

Just to give you another option, I'm extremely satisfied with my MCE2HDMI: https://serdashop.com/products/mce2hdmi

I'm running both my XT 5160 in CGA and my 386 DX-40 in EGA with it, through a HDMI-VGA adapter to a VGA CRT, the picture quality is extremely satisfying, including EGA scanlines.

Reply 18 of 25, by BitWrangler

User metadata
Rank l33t++
Rank
l33t++
Anaxagoras wrote on Yesterday, 09:43:
Yes, I’ve understood. The original CGA card has an RCA video output. But I think that model – the CGA installed in the original […]
Show full quote
Ozzuneoj wrote on Yesterday, 07:07:
Sorry if I'm misunderstanding what you're saying, but he was just saying to use the IBM CGA card (Color Graphics Adapter) that m […]
Show full quote
Anaxagoras wrote on Yesterday, 06:46:

Thanks rmay635703, good to know. But It sounds very expensive, at least to me.

Sorry if I'm misunderstanding what you're saying, but he was just saying to use the IBM CGA card (Color Graphics Adapter) that many IBM PCs and XTs would have originally come with. Specifically, the card shown here (they will have either a green or brown PCB). The RCA jack on it is a basic composite video output, so you can connect it directly to any TV with a composite video (yellow) input.

An XT would normally have come with one of four IBM video cards... Either a CGA card, a Monochrome Display Adapter card, or less commonly an Enhanced Graphics Adapter card... or if someone was made out of money, a rare and stupidly expensive Professional Graphics Controller card.

If your system didn't come with a video card or didn't come with an IBM CGA card, then you're probably best off just getting an OAK or Trident card will connect to a VGA monitor unless you can find an IBM CGA card cheap. There are some interesting things you can do with the composite video out on a CGA card (video demos that do crazy things to output more colors), but that's a pretty specific use case.

Yes, I’ve understood. The original CGA card has an RCA video output. But I think that model – the CGA installed in the original IBM PC-XT – is more expensive than the Trident 9000 VGA and probably hard to find too.

Of course, I know that there are different things.
The problem, or my scenario, is the following:
- PC-XT clone with CGA adapter.
- Monochrome monitor (12'') that’s about to stop working (used in my current setup).
- TV (14").
- TFT (17'').

To be honest, I don’t know what the best setup is for using my PC-XT without spending too much money.
I think the Trident 9000 graphics card plus a TFT monitor is a cheap option, but it means sacrificing the original look and feel.
Of course, the best thing would be to replace the current monitor with a ‘new’ one, but it’s very difficult to find one in good condition, it’s too heavy to post, and I don’t know how long I’ll be able to use it for.

For the other hand the original CGA card with video output to use in TV is the best option in terms of look and feel.

At the moment I created two searches on eBay, one for Trident card and other for CGA with video output.

Your problem with using the TV is that Spain appears to have used the PAL standard, whereas CGA TV-out is NTSC standard. It is possible that Japanese TV models will have a switch between NTSC and PAL but there are not many around like that. Possibly some modern LCD TVs will have a menu option to switch over. Some imported monitors for Commodore or Atari systems may have a switch also. However, with a PAL TV or video monitor that has lots of range in it's vertical hold control, you can get an NTSC picture to synch, but it will have no color, as the color system is different. This might be less of a problem if you have a card that can do CGA on monochrome and is aware that it is doing so and uses shades for colors. ATI wonder series for example and some Paradise cards.

If you get hold of an NTSC capable TV or monitor, then the video in this thread might help you get output out of your current card...
Re: HOMEDADE CGA

edit: should mention for those unfamiliar that ATI TV wonder is not the product I mean, that's for TV signal INPUT, the ones with output are the EGA Wonder etc.

Unicorn herding operations are proceeding, but all the totes of hens teeth and barrels of rocking horse poop give them plenty of hiding spots.

Reply 19 of 25, by rmay635703

User metadata
Rank l33t
Rank
l33t
Anaxagoras wrote on 2026-11-17, 12:44:
Hi guys! […]
Show full quote

Hi guys!

I guess my CGA monitor is close to dead 🙁 and I have a VGA monitor and an old CRT TV.

What of this ways is the best?
- Use the current CGA card --> External converter --> TV (CRT).

????

You shouldn't need a converter to hook IBM CGA card to a TV.

At least a mid range generic tv manufactured between 2001 to about 2009.
Some folks have even gotten Japanese VTR TVs and 60hz scart TVs to work with basically a home built adapter (resistor ladder optional)

If you have a RF only TV a simple adapter from radio shack and similar will adapt the yellow composite connector to channel 3.

I guess I would need a picture to see what equipment you have going on.

BitWrangler wrote on Yesterday, 14:52:
Your problem with using the TV is that Spain appears to have used the PAL standard, whereas CGA TV-out is NTSC standard. It is p […]
Show full quote
Anaxagoras wrote on Yesterday, 09:43:
Yes, I’ve understood. The original CGA card has an RCA video output. But I think that model – the CGA installed in the original […]
Show full quote
Ozzuneoj wrote on Yesterday, 07:07:

Sorry if I'm misunderstanding what you're saying, but he was just saying to use the IBM CGA card (Color Graphics Adapter) that many IBM PCs and XTs would have originally come with. Specifically, the card shown here (they will have either a green or brown PCB). The RCA jack on it is a basic composite video output, so you can connect it directly to any TV with a composite video (yellow) input.

An XT would normally have come with one of four IBM video cards... Either a CGA card, a Monochrome Display Adapter card, or less commonly an Enhanced Graphics Adapter card... or if someone was made out of money, a rare and stupidly expensive Professional Graphics Controller card.

If your system didn't come with a video card or didn't come with an IBM CGA card, then you're probably best off just getting an OAK or Trident card will connect to a VGA monitor unless you can find an IBM CGA card cheap. There are some interesting things you can do with the composite video out on a CGA card (video demos that do crazy things to output more colors), but that's a pretty specific use case.

Yes, I’ve understood. The original CGA card has an RCA video output. But I think that model – the CGA installed in the original IBM PC-XT – is more expensive than the Trident 9000 VGA and probably hard to find too.

Of course, I know that there are different things.
The problem, or my scenario, is the following:
- PC-XT clone with CGA adapter.
- Monochrome monitor (12'') that’s about to stop working (used in my current setup).
- TV (14").
- TFT (17'').

To be honest, I don’t know what the best setup is for using my PC-XT without spending too much money.
I think the Trident 9000 graphics card plus a TFT monitor is a cheap option, but it means sacrificing the original look and feel.
Of course, the best thing would be to replace the current monitor with a ‘new’ one, but it’s very difficult to find one in good condition, it’s too heavy to post, and I don’t know how long I’ll be able to use it for.

For the other hand the original CGA card with video output to use in TV is the best option in terms of look and feel.

At the moment I created two searches on eBay, one for Trident card and other for CGA with video output.

Your problem with using the TV is that Spain appears to have used the PAL standard, whereas CGA TV-out is NTSC standard. It is possible that Japanese TV models will have a switch between NTSC and PAL but there are not many around like that. Possibly some modern LCD TVs will have a menu option to switch over. Some imported monitors for Commodore or Atari systems may have a switch also. However, with a PAL TV or video monitor that has lots of range in it's vertical hold control, you can get an NTSC picture to synch, but it will have no color, as the color system is different. This might be less of a problem if you have a card that can do CGA on monochrome and is aware that it is doing so and uses shades for colors. ATI wonder series for example and some Paradise cards.

If you get hold of an NTSC capable TV or monitor, then the video in this thread might help you get output out of your current card...
Re: HOMEDADE CGA

edit: should mention for those unfamiliar that ATI TV wonder is not the product I mean, that's for TV signal INPUT, the ones with output are the EGA Wonder etc.

Scratch what I wrote, 🤣 Spain,

One of my friends was able to crank the vhold on a very old b&w NTSC tv to get a PAL spectrum working in the 90's image was still sort of wrong but you could use it.

I do remember some of the cheap small generic off brand 13/14" LCD "hd tvS" sold in the 2001-2009 era as at least syncing to PAL and NTSC YMMV but if you can find one they should be fairly cheap.

Last edited by rmay635703 on 2026-11-19, 15:31. Edited 1 time in total.