READ.ME
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³ ³
³ Holtek VL-IDE ReadMe ³
³ ³
³ Version : 1.53 ³
³ ³
³ Date : 01/05/1995 ³
³ ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
This diskette contains the DOS device driver, Windows IDE Driver and
driver setup program for Holtek HT-6560A VL-Bus IDE Controller/Adapter.
Diskette Content
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
Filename Description
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
READ.ME This file
IDESETUP.COM Driver Setup Program
HTIDE.SYS DOS Device Driver
HTIDE.386 Windows IDE Driver
HTCDPRE.COM ATAPI CD-ROM Device Driver Preprocessor V2.00
Setup DOS Device Driver
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
Run IDESETUP to setup DOS Device Driver. The setup program will
install the DOS device driver (HTIDE.SYS) to directory 'C:\HTIDE',
and add the following command to your CONFIG.SYS (if required).
DEVICE = C:\HTIDE\HTIDE.SYS [/D0=rt, at [, m]] [/D1=rt, at [, m]]
If CONFIG.SYS is modified, the original content will be saved in
CONFIG.HTK, CONFIG.000, CONFIG.001, .... CONFIG.999 in sequence
if the previous file exists. Otherwise, a sample CONFIG.SYS named
CONFIG.HTK is created in directory C:\HTIDE.
Parameters Description :
All parameters are non-case sensitive. [ ] means the parameter
is optional.
/D0 = rt, at [, m]
/D1 = rt, at [, m]
/Dn defines the cycle time interfacing with drive n.
rt = Recovery Time
The valid values range from 4 to 17
The default is 15.
at = Active Time
The valid values range from 2 to 15
The default is 15.
m = Block size for Multiple Mode
1 - Multiple mode is disabled
Example :
DEVICE=C:\HTIDE\HTIDE.SYS /D0=5,5 /D1=8,8,1
Setup Windows IDE Driver
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
Setup Windows IDE Driver will setup the DOS IDE device driver for
you automatically, and modify the CONFIG.SYS. The IDESETUP program
copies HTIDE.386 to the directory C:\HTIDE, modifies the SYSTEM.INI
of Windows. It replaces
device=*wdctrl
with
DEVICE=C:\HTIDE\HTIDE.386
in the [386Enh] section of SYSTEM.INI. And always set the command
32BitDiskAccess=ON
The original content of SYSTEM.INI will be saved in SYSTEM.HTK,
SYSTEM.000, SYSTEM.001, .... SYSTEM.999, SYSTEM.BGY in sequence if
the previous file exists.
Trouble Shooting
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
1. When the system clock is changed, or move the drive (drives) to
another PC system, you must run IDESETUP program to resetup the
cycle time.
2. The IDESETUP program setups the cycle time for each drive
automatically. Sometimes it derives the cycle time improperly.
You can enlarge the cycle time to the drive when you can not
access the drive normally. Modify the command line parameters
rt, at for enlarging cycle time.
3. Some powerful IDE function would be disabled when driver detects
ATAPI CD-ROM was attahed. This will decrease the performance of
your hard disks. For conquering this spot, we supply HTCDPRE.COM,
the ATAPI CD-ROM Device Driver Preprocessor, to cooperate with
the IDE Controller.
Please add the following command
C:\HTIDE\HTCDPRE /D:<CD-ROM Device Driver Name>
before the MSCDEX command line in your AUTOEXEC.BAT, or run it
before the MSCDEX is executed. Please refer your CD-ROM device
driver or the MSCDEX program about explanation of parameter /D.