Ok, i make think about fearture connector in second 765VL-draft. It has low prio, sorry.

I hope, we got 15 minimum order for PCB in a german forum. Then i can order 25 pieces and sell 10 pieces pcb with compoment list here.
Who want it ? Pleas write me a PN with country, where you live. (i can ship worldwide, but i prefer: I ship more pieces to one people in USA and this people share pcb)

Notice:
One has borrowed me ARK1000VL and it is compared with Trio64V+ VLB on System Abit AN4R307 & AMD 5x86 @160Mhz.
Ark1000VL is faster than Trio64V+, but distance is in most case zero, only DOOM is ARK slight faster ( ARK 59.04 / Trio64V+ 58,63)

regards
matt

PCBs is arrivied, since friday. ( i got 50 pieces, over half is reservered )

I'll write few people for selling of pcb. Pleas be patient.

regards
matt

Madao wrote on 2021-09-13, 03:42:

PCBs is arrivied, since friday. ( i got 50 pieces, over half is reservered ) […]
Show full quote

PCBs is arrivied, since friday. ( i got 50 pieces, over half is reservered )

I'll write few people for selling of pcb. Pleas be patient.

regards
matt

nice! I've been monitor this thread on and off thru time , kudos on finishing the project!!!!
I am interested in one or two if they can be spared 😀

Nice one! I'm interested as well, but I'll wait for the next round,
as I need it to also have a feautre connector.
Keep up the good work

I want a PCB too please!

Have hot air rework station at the ready, and will happily sacrifice a TrioV+ PCI card 😀

Damn, that looks so hot! I would like to have one too 😀

I would like one as well.

I’m interested in one if boards are still available. Thanks.

I'm also interested 😀

Me too!

Lol, I can see S3 Trio V+ prices skyrocketting on ebay already as an army of hotgun wielders convert them all to VLB!

In the end my mistake of baking my non-working TrioV64+ may end up as a happy ending as a donor chip in timely fashion! 😁

Thanks, got my PCB + Building Kit.
Did not yet assemble it 😀

Now: I can sell pcb

a pcb cost 8 USD and 10$ outside EU, inside EU 5,5$

I have ~10 piece PCB left.

Pleas write me a private message, if you're interessing on pcb.

Of coruse, only trio64V+
But Virge (325) may run on this PCB with patched ROM and heavy modified virge driver.

And a next message.

I got couple graphic card, one is Trio64V2/DX. This chip has official no VLB support. I have soldered him to VLB . Yes, VLB Support is removed. (It locks 486 local bus very hard )

Do you know if there is sufficient space surrounding the memory pads to install SOJ-40 sockets? I suspect not due to the caps.

No, it is never designed for using of SOJ Socket. (i hate SOJ /PLCC SMD Socket 😒 )

Madao wrote on 2021-10-28, 15:53:

No, it is never designed for using of SOJ Socket. (i hate SOJ /PLCC SMD Socket 😒 )

I don't much care for them either but there is a time and a place to use them.

Not to mention the footprint is identical so it doesn't take much to accommodate them (physical clearance)

I was going to put them on, but looks like caps are in the way. So I guess I'm not putting them on.

perhaps you could cut a small notch in the bottom of the socket to clearance it for the bypass cap?