Aopen CRW5232/ARR LED lights up then dies \ VOGONS

Aopen CRW5232/ARR LED lights up then dies

Topic actions

First post, by kotel

Posted on 2024-03-04, 20:24

kotel Offline

Rank Oldbie

Rank: Oldbie
Posts: 613
Joined: 2024-02-15, 14:58
Location: On lifes edge

A while ago i got this Aopen CRW5232/ARR CD writer. After pluging it in, the LED lights up for a quarter of a second, then the drive dies. Drive isn't detected at all. Any ideas what might be the cause of this?

Always has the weirdest issues happen, and always is all alone with them

Reply 1 of 7, by dominusprog

Posted on 2024-03-04, 20:37

dominusprog Offline

Rank Oldbie

Rank: Oldbie
Posts: 967
Joined: 2022-07-02, 00:52
Location: Innsmouth

You have to inspect the board. Post a photo if you can.

A-Trend ATC-1020 V1.1 ❇ Cyrix 6x86 150+ @ 120MHz ❇ 32MiB EDO RAM (8MiBx4) ❇ A-Trend S3 Trio64V2 2MiB
OPTi MAD16 / Creative Vibra16XV ❇ 8.4GiB Quantum Fireball ❇ Win95 OSR2 Plus!

Reply 2 of 7, by kotel

Posted on 2024-03-05, 11:57

kotel Offline

Rank Oldbie

Rank: Oldbie
Posts: 613
Joined: 2024-02-15, 14:58
Location: On lifes edge

dominusprog wrote on 2024-03-04, 20:37:

You have to inspect the board. Post a photo if you can.

Didn't spot any obviously broken compotents. After a while, The RICOH RL3E804 starts slowly heating up.

Always has the weirdest issues happen, and always is all alone with them

Reply 3 of 7, by dominusprog

Posted on 2024-03-05, 15:58

dominusprog Offline

Rank Oldbie

Rank: Oldbie
Posts: 967
Joined: 2022-07-02, 00:52
Location: Innsmouth

First, check the fuse (first pic, top left). Then you'll have to check the mosfets.

A-Trend ATC-1020 V1.1 ❇ Cyrix 6x86 150+ @ 120MHz ❇ 32MiB EDO RAM (8MiBx4) ❇ A-Trend S3 Trio64V2 2MiB
OPTi MAD16 / Creative Vibra16XV ❇ 8.4GiB Quantum Fireball ❇ Win95 OSR2 Plus!

Reply 4 of 7, by kotel

Posted on 2024-03-05, 16:41

kotel Offline

Rank Oldbie

Rank: Oldbie
Posts: 613
Joined: 2024-02-15, 14:58
Location: On lifes edge

dominusprog wrote on 2024-03-05, 15:58:

First, check the fuse (first pic, top left). Then you'll have to check the mosfets.

You mean L1? It has 1 ohm. Mosfet Q1 has 3.3v on base and Q2 1.89v on base too. No shorts to ground. Also, i was wrong about that RICOH chip. Its getting really warm after a couple of seconds. Any ideas?

Always has the weirdest issues happen, and always is all alone with them

Reply 5 of 7, by dominusprog

Posted on 2024-03-05, 19:39

dominusprog Offline

Rank Oldbie

Rank: Oldbie
Posts: 967
Joined: 2022-07-02, 00:52
Location: Innsmouth

It's probably gone bad. These chips aren't supposed to get hot, except for the chip on the left (pic 3).

A-Trend ATC-1020 V1.1 ❇ Cyrix 6x86 150+ @ 120MHz ❇ 32MiB EDO RAM (8MiBx4) ❇ A-Trend S3 Trio64V2 2MiB
OPTi MAD16 / Creative Vibra16XV ❇ 8.4GiB Quantum Fireball ❇ Win95 OSR2 Plus!

Reply 6 of 7, by kotel

Posted on 2024-03-06, 19:22

kotel Offline

Rank Oldbie

Rank: Oldbie
Posts: 613
Joined: 2024-02-15, 14:58
Location: On lifes edge

dominusprog wrote on 2024-03-05, 19:39:

It's probably gone bad. These chips aren't supposed to get hot, except for the chip on the left (pic 3).

Is there anything else i can test? Also, are there any similar replacements for that RICOH chip? I can't find anyone selling that exact chip.

Always has the weirdest issues happen, and always is all alone with them

Reply 7 of 7, by nhattu1986

Posted on 2024-03-07, 03:04

nhattu1986 Offline

Rank Member

Rank: Member
Posts: 107
Joined: 2019-04-05, 02:02

kotel wrote on 2024-03-06, 19:22:

dominusprog wrote on 2024-03-05, 19:39:

It's probably gone bad. These chips aren't supposed to get hot, except for the chip on the left (pic 3).

Is there anything else i can test? Also, are there any similar replacements for that RICOH chip? I can't find anyone selling that exact chip.

I don't think there are anything you can check, this chip basically the heart of the drive, if it got shorted (get so hot when apply power) then you had better find another drive and moving on
you can keep the laser/spindle and use them as replacement part.

Go to top of page Go to top of page

Back to General Old Hardware