VOGONS

Search

Common searches

DataExpert 367C motherboard not working

Topic actions

First post, by jnemo2004

Posted on 
User metadata
Rank Member
Rank
Member

https://theretroweb.com/motherboards/s/dataexpert-367c

Hello good morning. I recently bought this motherboard with a lot of corrosion to try to repair it.
I have removed all affected components and attempted to repair damaged tracks.
I have reviewed all the clues with the help of a graph and everything seems to indicate that they have been repaired.
Once the damaged tracks were repaired, I soldered the removed components and replaced the broken components.
I just haven't put in the 4 SIMM sockets from bank 0 since I thought I could use the 4 SIMMs from bank 1.
I have installed an AMD 386DX33 processor, I have connected the board and it does not work.
All voltages and CLKs are present, the RST signal too but the diagnostic board is at 00, it does not start.
The questions are the following:
1.- According to the information on The Retro Web, the board must always use the SIMMs from bank 0. Do they have to be soldered again?
2.- I have been able to verify that some connections of the DIN5 connector are made using hidden tracks. Pin No. 4, which must be connected to GND, does so through L1. I don't know if it's correct.

Attachments

  • Imagen 1.jpg
    Filename
    Imagen 1.jpg
    File size
    135.66 KiB
    Views
    421 views
    File license
    Public domain
  • Imagen 2.jpg
    Filename
    Imagen 2.jpg
    File size
    101.96 KiB
    Views
    421 views
    File license
    Public domain
  • Imagen 3.jpg
    Filename
    Imagen 3.jpg
    File size
    93.67 KiB
    Views
    421 views
    File license
    Public domain
  • Imagen 4.jpg
    Filename
    Imagen 4.jpg
    File size
    161.24 KiB
    Views
    421 views
    File license
    Public domain
  • Imagen 5.jpg
    Filename
    Imagen 5.jpg
    File size
    159.64 KiB
    Views
    421 views
    File license
    Public domain

Reply 1 of 10, by jnemo2004

Posted on 
User metadata
Rank Member
Rank
Member

More images

Attachments

  • Imagen 6.jpg
    Filename
    Imagen 6.jpg
    File size
    153.62 KiB
    Views
    419 views
    File license
    Public domain
  • Imagen 7.jpg
    Filename
    Imagen 7.jpg
    File size
    39.39 KiB
    Views
    419 views
    File license
    Public domain
  • Imagen 8.jpg
    Filename
    Imagen 8.jpg
    File size
    28.97 KiB
    Views
    419 views
    File license
    Public domain

Reply 3 of 10, by jnemo2004

Posted on 
User metadata
Rank Member
Rank
Member

Hello, good afternoon.
I have re-soldered the Bank0 SIMM sockets that I had previously removed to check if the tracks were okay. I have also put in the 4 SIMMs from bank 0. I have rechecked the tracks that had corrosion to see if they are well connected and they are all good but the board still does not work.
The only thing I find strange is that with an oscilloscope I don't see signals in Keyboard CLK and DATA but I don't know when they should be present so I'm not saying they are bad.
I have tried to find the Data sheet for the UNIchip U4800-VLX Chipset.
Do any of you have this data sheet?
Thanks and regards.

Attachments

Reply 5 of 10, by jnemo2004

Posted on 
User metadata
Rank Member
Rank
Member

It looks like a hole but it isn't. It must have been a reflection. Thank you very much and best regards.

Attachments

Reply 8 of 10, by jnemo2004

Posted on 
User metadata
Rank Member
Rank
Member

Hello good morning.
I would like to have a checking system when I start with a motherboard.
The one I have is very basic:
1.- I check that the power lines in the main connector are not shorted.
2.- Without adding memory, CPU and graphics card, I connect the PSU and check the following voltages:
In ISA socket, +5v, -5v, +12v, -12v
In SIMM sockets +5v
In processor socket, the corresponding voltage.
3.- I check the following CLKs:
In ISA socket, 8 Mhz (sometimes lower)
In board:
CLK 34.768Khz
CLK 14 Mhz
In processor socket, the corresponding frequency.
I would also like to check the communication of the Keyboard with the KBC (CLK and DATA) but I don't know how to do it
4.- I insert the diagnostic card and check:
The voltages (again)
the RST signal

5.- I would like to add more verifications. If any of you can add some, I will appreciate it.
For example, how to know each of the main chips is working, processor, chipset, etc.

Reply 9 of 10, by PD2JK

Posted on 
User metadata
Rank Oldbie
Rank
Oldbie

RTC crystal working as well? You said all clocks, so I guess it works.

i386 16 ⇒ i486 DX4 100 ⇒ Pentium MMX 200 ⇒ Athlon Orion 700 | TB 1000 ⇒ AthlonXP 1700+ ⇒ Opteron 165 ⇒ Dual Opteron 856

Go to top of page Go to top of page
Back to General Old Hardware
Close window
Close window