Capacitors can be replaced. Also, try vinegar to dissolve some of the corrosion and oil to lubricate the battery door. You can always dunk it on isopropyl alcohol to clean it later.

shan2752 wrote on 2025-07-11, 23:56:

Getting new components, where possible, increases the odds of that happening. I would get the PCMidi Add on just in case the LAPC fails. I have an SCC-1 in my P3, so I am preparing for that to eventually die. It is approaching 30 years old now, and capacitors degrade over time even without use.

Fair enough, but Intelligent Mode MPU is one thing: I could get an Ensoniq SoundScape-based card to cover that end pretty well. Emulation-based options aside, is there anything out there that would effectively serve as a 1-to-1 replacement of a Roland LA device enabling proper instruments for music AND SOUND EFFECTS on supporting DOS games that pre-date General MIDI? The list of such titles from MicroProse & LucasArts is not that small; for fans of Origin and/or Sierra things get even more complicated because of the different Roland LA generations and how games varied in their support for each.

The PicoGus with McCake or the TM32 both come to mind. However, they both serve a different purpose than the MK1869.

Kahenraz wrote on 2025-07-14, 19:21:

The PicoGus with McCake or the TM32 both come to mind. However, they both serve a different purpose than the MK1869.

Both are Munt-based: emulated, requiring the Roland ROMs.

keropi wrote on 2024-09-02, 11:22:

- ISA 16bit passthrough for expansion boards with midi/audio/usb i/o connector for integration

So tech specs (pcb schematics) are not available for public. However can you confirm that it's 1:1 parallel ISA bus implementation? Going over with ohmmeter seems to be confirming it.
There are many late ISA era MBs with only one ISA slot. It could be possible to marry MK1869 and Picogus v1.x hw fork since it's open hardware

vutt wrote on 2025-07-18, 13:21:

So tech specs (pcb schematics) are not available for public. However can you confirm that it's 1:1 parallel ISA bus implementation? Going over with ohmmeter seems to be confirming it.

the headers are 1:1 and on the backside the silkscreen has the pinout of both headers and the expansion connector behind the jacks

Concerning the MK1869 Extreme, the pre-order ended earlier this week (15th). Did you get a viable number for getting into production?

Just a question.. I signed up for the pre-sale and wanted to make sure I didnt miss anything..

You will email us and then we send the 50% deposit.. or was there somewhere we were supposed to send it upon filling out the form?

Thanks!

Angus.Young wrote on Yesterday, 01:03:

Just a question.. I signed up for the pre-sale and wanted to make sure I didnt miss anything..

You will email us and then we send the 50% deposit.. or was there somewhere we were supposed to send it upon filling out the form?

Thanks!

You should have received an email (check your spam filters and whatnot) with details about how to send the 50% upfront. Search your email account for "Leo Dallas" - I won't share the email address itself here, to help prevent bots from finding it when crawling vogons. Every little bit of obscurity helps with spam 😉

June 27th was when I received my email.

Aladim wrote on 2025-07-18, 23:41:

Concerning the MK1869 Extreme, the pre-order ended earlier this week (15th). Did you get a viable number for getting into production?

yes the production is moving forward - interest was more than expected too!

Angus.Young wrote on Yesterday, 01:03:

Just a question.. I signed up for the pre-sale and wanted to make sure I didnt miss anything..

You will email us and then we send the 50% deposit.. or was there somewhere we were supposed to send it upon filling out the form?

Thanks!

all emails with payment details have already gone out, usually a few hrs afrer the form was filled.
if you did not get anything please use the contact form on the site and I will re-send the info

keropi wrote on Yesterday, 06:27:

yes the production is moving forward - interest was more than expected too! […]
Show full quote

Aladim wrote on 2025-07-18, 23:41:

Concerning the MK1869 Extreme, the pre-order ended earlier this week (15th). Did you get a viable number for getting into production?

yes the production is moving forward - interest was more than expected too!

Angus.Young wrote on Yesterday, 01:03:

Just a question.. I signed up for the pre-sale and wanted to make sure I didnt miss anything..

You will email us and then we send the 50% deposit.. or was there somewhere we were supposed to send it upon filling out the form?

Thanks!

all emails with payment details have already gone out, usually a few hrs afrer the form was filled.
if you did not get anything please use the contact form on the site and I will re-send the info

I checked and nothing.. possibly I mistyped something not sure.. but I have filled the contact form.

Thank You!

Angus.Young wrote on Yesterday, 14:56:

I checked and nothing.. possibly I mistyped something not sure.. but I have filled the contact form.

Thank You!

saw the message and sent the email again , hope this time it goes through!

keropi wrote on Yesterday, 15:13:

Angus.Young wrote on Yesterday, 14:56:

I checked and nothing.. possibly I mistyped something not sure.. but I have filled the contact form.

Thank You!

saw the message and sent the email again , hope this time it goes through!

Got it and sent paypal.. not sure as I still couldn't find first message but second was no issue.

Much appreciated!

vutt wrote on 2025-07-18, 13:21:

keropi wrote on 2024-09-02, 11:22:

- ISA 16bit passthrough for expansion boards with midi/audio/usb i/o connector for integration

So tech specs (pcb schematics) are not available for public. However can you confirm that it's 1:1 parallel ISA bus implementation? Going over with ohmmeter seems to be confirming it.
There are many late ISA era MBs with only one ISA slot. It could be possible to marry MK1869 and Picogus v1.x hw fork since it's open hardware

Looking forward to emulating a GUS on my GUS. 😁