VOGONS


Reply 60 of 64, by Tiido

User metadata
Rank l33t
Rank
l33t

Aluminizing the phosphors definitely helps but what actually solved the problem was pure materials that didn't offgas impurities during use. Better getters to absorb what did come out and much better vacuums help also.
There is one place where phoshpor burn-in actually is a big concern and it is projection stuff. My Barco Data 801s has only about 4k hours on it and doesn't yet have visible darkening of the phosphor area that glows, but I have seen photos of stuff some 15k hours old and those have very noticable burned in sections. At some point, recoating the phoshpors was a thing for these projection things, but from what I remember the last place that did it commercially shut down several years ago.

One thing that can help longer term is to just increase filament voltage slightly. My nice Nokia monitor has 30k hours on it and it took actually a long time for it to "warm up" so that it won't black crush anymore, roughly 30 minutes. Some months ago I upped the filament voltage from 6.3V to 6.5V and now it takes some 10 minutes to reach the warmup state where it stops black crushing, a dramatic improvement over before. Higher boost probably improves things even more but I fear the lifetime will be shortened too much. Brightness also improved and I could slightly improve focus over earlier state, so this has been a big win overall. The monitor is nearing EOL and things like this become necessary to get more useful life out of these things...

Those companies definitely do something fun. It would be something I'd like to try out too, but doing this on a high end color monitor is not gonna be an easy task. Those guns are much more complex than the BW things often repaired this type of way. One company I know that does color stuff has a limited stock of guns to use for this task and sooner or later it'll run out... so ability to actually manufacture new stuff will become necessary eventually. Phosphors recoat for my projection tubes should be within reach though, as long as cathodes stay ok enough (they have much more robust cathodes, due to *much* higher beam currents)

T-04YBSC, a new YMF71x based sound card & Official VOGONS thread about it
Newly made 4MB 60ns 30pin SIMMs ~
mida sa loed ? nagunii aru ei saa 😜

Reply 61 of 64, by The Solutor

User metadata
Rank Member
Rank
Member
Tiido wrote on 2026-09-11, 20:38:

Aluminizing the phosphors definitely helps but what actually solved the problem was pure materials that didn't offgas impurities during use. Better getters to absorb what did come out and much better vacuums help also.
There is one place where phoshpor burn-in actually is a big concern and it is projection stuff. My Barco Data 801s has only about 4k hours on it and doesn't yet have visible darkening of the phosphor area that glows, but I have seen photos of stuff some 15k hours old and those have very noticable burned in sections. At some point, recoating the phoshpors was a thing for these projection things, but from what I remember the last place that did it commercially shut down several years ago.

Yep, projection CRTs are in their own league, given the energy for square cm, is orders of magnitudes higher

One thing that can help longer term is to just increase filament voltage slightly. My nice Nokia monitor has 30k hours on it and it took actually a long time for it to "warm up" so that it won't black crush anymore, roughly 30 minutes. Some months ago I upped the filament voltage from 6.3V to 6.5V and now it takes some 10 minutes to reach the warmup state where it stops black crushing, a dramatic improvement over before. Higher boost probably improves things even more but I fear the lifetime will be shortened too much. Brightness also improved and I could slightly improve focus over earlier state, so this has been a big win overall. The monitor is nearing EOL and things like this become necessary to get more useful life out of these things...

Oh I think 6.5V can still be considered tolerance, not overvolting, I think you can go much higher, like 7/8/9V w/o beeing much worried that the filament burns.

To put in perspective I still have a working old school incandescent lamp (the ones running on vacuum, not inert gas) that my grandmother brought here from the US in 1920 or so.

It worked for years in the US, it worked for decades here, it's still working in 2026 (albeit the glass is darkened by the sublimating filament, that's why vaccum was replaced by inert gas).

And a lamp being a lamp runs at way higher temps than a vaccum tube heater

Those companies definitely do something fun. It would be something I'd like to try out too, but doing this on a high end color monitor is not gonna be an easy task. Those guns are much more complex than the BW things often repaired this type of way. One company I know that does color stuff has a limited stock of guns to use for this task and sooner or later it'll run out... so ability to actually manufacture new stuff will become necessary eventually. Phosphors recoat for my projection tubes should be within reach though, as long as cathodes stay ok enough (they have much more robust cathodes, due to *much* higher beam currents)

Definitely not an easy task, but (I guess) that if you do a single thing for a life you earn an expertise unknown to "normal mortals"

Think to how much experience you need to calibrate purity/deflection/convergence/focusing on a 1960/70/80 delta TV color, most tecnicians who worked in that era can do that "blindfolded" but an amateur that attempt for the first time in 2026, can spend weeks before getting a decent result (or give up).

Reply 62 of 64, by wierd_w

User metadata
Rank l33t
Rank
l33t

I have a KDS 19" VGA CRT upstairs that I use on occasion for doing techwork with. It works, but is starting to act a little squirrely.

In general, I use LCDs these days.

Reply 63 of 64, by Tiido

User metadata
Rank l33t
Rank
l33t
The Solutor wrote on 2026-09-11, 22:07:

Think to how much experience you need to calibrate purity/deflection/convergence/focusing on a 1960/70/80 delta TV color, most tecnicians who worked in that era can do that "blindfolded" but an amateur that attempt for the first time in 2026, can spend weeks before getting a decent result (or give up).

Converging is something I have done many times, and always reaching better results than the factory conf although it does take a whole day sometimes but partially because I have chased incremental improvements. There's often some actual defect in the yoke, even in pro stuff, that makes one area in the screen unwilling to bow to my control... There have been cases where I use up less of the magnet strips than originally used, and still get significantly better result over the stock case 🤣. I would love to have access to the jigs used at factories to do this sort of stuff though... But when I first started, there was definite lack of experience and the process was not smooth or fast by any means. People definitely give up, and often have worse result than before they started... I wish the converging was as simple as on the projectors, with every color separately adjustable with no interplay 🤣

But as far as filament goes, I actually purposefully tried to burn out one in a relatively recent Philips tube, and I reached 17V, without burning it out. I had no higher power supply to use at that moment and there was a time crunch to get things out of the way prior to my move to Norway so I never did find out when actually the thing dies... For the moment I'll live with the slightly increased voltage in the Nokia, if it gets bad again I'll increment it higher. When I have some excess monitor or TV to play with, I'll actually want to run an experiment with dramatically increased filament to see what sort of effect it'll have on the lifetime of the device. Variety of literature mentions "much reduced" lifetime, but there actually never are any numbers presented by how much...

T-04YBSC, a new YMF71x based sound card & Official VOGONS thread about it
Newly made 4MB 60ns 30pin SIMMs ~
mida sa loed ? nagunii aru ei saa 😜

Reply 64 of 64, by The Solutor

User metadata
Rank Member
Rank
Member
Tiido wrote on 2026-09-12, 07:55:

I wish the converging was as simple as on the projectors, with every color separately adjustable with no interplay 🤣

Speaking of CRT projectors I never had many cases of repair, just few installation of brand new units, which wasn't hard.

But I had to fight with 3 LCD projectors, from Sharp. Absolutely not something for faint of heart, given usually they come from bars or other public places, where at the time smoking was allowed.

So fixing them basically meant replacing the lamp (around 1200€ in todays money), and cleaning the internals from dirt and nicotine which, in turn, meant taking them apart piece by piece. A triumph of mirrors, prisms, lenses, dichroic filters, Fresnel lens and so on, then reassemble the thing and align everything back.

But as far as filament goes, I actually purposefully tried to burn out one in a relatively recent Philips tube, and I reached 17V, without burning it out. I had no higher power supply to use at that moment and there was a time crunch to get things out of the way prior to my move to Norway so I never did find out when actually the thing dies... For the moment I'll live with the slightly increased voltage in the Nokia, if it gets bad again I'll increment it higher. When I have some excess monitor or TV to play with, I'll actually want to run an experiment with dramatically increased filament to see what sort of effect it'll have on the lifetime of the device. Variety of literature mentions "much reduced" lifetime, but there actually never are any numbers presented by how much...

Likely stats aren't there because the lack of consistent data, maybe some CRT maker had something, but they took them for internal use.

Everything else is personal experience that can vary wildly depending the CRT maker, the age, the era and so on.

Btw, I think that back in the vacuum tubes day there were small transformers with 6.3V input and multiple outputs, sold exactly for the purpose we are discussing about