VOGONS


Battle of the platforms: socket 939!

Topic actions

Reply 460 of 616, by FullYes

User metadata
Rank Member
Rank
Member
nd22 wrote on 2026-03-15, 05:47:
UL8 is the only Abit board with a ULI chipset for socket 939; it is less wide than the ATX standard however it is not micro-ATX. […]
Show full quote

UL8 is the only Abit board with a ULI chipset for socket 939; it is less wide than the ATX standard however it is not micro-ATX. Everything that you get comes only from the M1689 chipset, there are no extra controllers.
The main ATX connector is of the 24 pin variety which makes the board easy to use with modern power supplies. It is ideally positioned at the right edge of the board; unfortunately the P4 connector is right in the middle of the board.
You get 2 SATA 150 connectors that are fully compatible with SSD's and optical drives - a huge advantage! Because I used a WD raptor in the VIA system I also used one in this system for all drive-related tests.
The chipset hides under the blue heatsink and barely gets a little warm!

I seem to remember the ABit UL8 (and maybe ULI 1689 boards in general?) had some interesting memory dividers including a few higher ones. I can't remember now, but perhaps you could have a look next time you use this board?

I had a UL8 paired with a San Diego 4000+ in around 2007, I was quite late to the party after hanging on to my athlon XP system for too long. By then the parts were very cheap. I then changed it to nforce4 ASUS A8N-SLI Deluxe with PCI-E, but this was a terrible board for overclocking. I had some XMS 4400 PRO DDR 550 ram that I was unable to take advantage of as the FSB speed could not get there with the A8N, I don't even think it had a higher option than 1:1. What is worse, it would not o/c even as well as the Abit UL8. I never understood why, it was either a terrible board or I was doing something wrong.

I always wondered if the UL8 could run the RAM at perhaps 2:1 ratio DRAM:FSB (i can't remember if it went that high?) but this would only work if you had an unlocked CPU as you would need something like 133MHz FSB to give you 266/533 DDR. and a 22x multiplier to get back up to the right clock speed.

System 1: K6-3+ MS-5158 (430TX), Voodoo3, AWE64
System 2: Athlon XP-M 2800+ SL-75KAV (KT133A) Quadro FX 1000, Vibra 16
System 3: 775i65g E5800, FX5900XT, Audigy 2ZS
System 4: i7-2600k, P8P67-M, GTX 460

Reply 461 of 616, by agent_x007

User metadata
Rank Oldbie
Rank
Oldbie

DRAM clock for S939 comes from CPU frequency (using dividers).
For example :
DDR 550 (real clock 275MHz), would require CPU speed of :
1) 2200MHz (8x divider)
2) 2750MHz (10x divider)
3) 3300MHz (12x divider) <= HIGHLY unlikely to work on dual core CPU on S939.

There are multiple ways to get to those clock speeds (multiplier/"base"), few examples :
11 x 300MHz
11 x 200MHz
10x 275MHz
10x 220MHz

There is no point in forcing Intel's way of memory clocking on platform that simply doesn't do it that way.
You also don't especially need that extra base clock for performance (IMC takes care of that).
HTT* base, manipulation is nice option to have if you want to bypass some limitations (CPUs with half multipliers can be a pain to "match speed" of DRAM with other platforms).
(*no FSB on K8, similar to Intel's LGA 1366 and later platforms)

Last edited by agent_x007 on 2026-09-22, 12:37. Edited 1 time in total.

Reply 462 of 616, by nd22

User metadata
Rank l33t
Rank
l33t
zuldan wrote on 2026-09-21, 09:18:
Very impressive! […]
Show full quote
nd22 wrote on 2026-09-13, 14:09:
zuldan wrote on 2026-09-11, 03:21:

nd22 do you have the ABit Fatal1ty AN8 SLI with ABIT Guru Front Panel (GP-02) in your collection?

You mean this one:

Very impressive!

How about this one?

The attachment 20260921_160310.jpeg is no longer available

I have already shown my 3 AV8 in this post: Re: Battle of the platforms: socket 939!
I do not have the full package of this board but I have 3 guru clock version 1, 4 version 2 and no model 3 which is exceedingly rare:

Reply 463 of 616, by nd22

User metadata
Rank l33t
Rank
l33t

I tried a Thermaltake pci-express extender and it does not work on either AX8 or AN8: https://www.thermaltake.com/tt-premium-pci-e- … nder-300mm.html
I tried a second one - a no name Chinese copy - and both boards refuse to work with it and halt with postcode 25.
I will try tonight another pci-express riser - options are running out...

Reply 464 of 616, by zuldan

User metadata
Rank Oldbie
Rank
Oldbie
nd22 wrote on 2026-09-22, 06:40:

I have already shown my 3 AV8 in this post: Re: Battle of the platforms: socket 939!
I do not have the full package of this board but I have 3 guru clock version 1, 4 version 2 and no model 3 which is exceedingly rare:

Great clock collection. Yes very rare!

Reply 465 of 616, by FullYes

User metadata
Rank Member
Rank
Member
agent_x007 wrote on 2026-09-21, 23:17:
DRAM clock for S939 comes from CPU frequency (using dividers). For example : DDR 550 (real clock 275MHz), would require CPU spee […]
Show full quote

DRAM clock for S939 comes from CPU frequency (using dividers).
For example :
DDR 550 (real clock 275MHz), would require CPU speed of :
1) 2200MHz (8x divider)
2) 2750MHz (10x divider)
3) 3300MHz (12x divider) <= HIGHLY unlikely to work on dual core CPU on S939.

There are multiple ways to get to those clock speeds (multiplier/"base"), few examples :
11 x 300MHz
11 x 200MHz
10x 275MHz
10x 220MHz

There is no point in forcing Intel's way of memory clocking on platform that simply doesn't do it that way.
You also don't especially need that extra base clock for performance (IMC takes care of that).
HTT* base, manipulation is nice option to have if you want to bypass some limitations (CPUs with half multipliers can be a pain to "match speed" of DRAM with other platforms).
(*no FSB on K8, similar to Intel's LGA 1366 and later platforms)

Thank you. I did overclock at 1:1 on both the UL8 and A8N. The UL8 would go well above 225Mhz but the A8N would not. I ended up swapping for an opteron 185 with the A8N but this was not any better for o/c.

Later I built another machine with a 4000+ for a family member that could do 3GHz but I can’t remember what board I used. had to run the memory on a Lower divider to achieve it (I had sold the good ram at this point!) but it worked. Damn I’m going to have to look through my emails now to see what I used.

System 1: K6-3+ MS-5158 (430TX), Voodoo3, AWE64
System 2: Athlon XP-M 2800+ SL-75KAV (KT133A) Quadro FX 1000, Vibra 16
System 3: 775i65g E5800, FX5900XT, Audigy 2ZS
System 4: i7-2600k, P8P67-M, GTX 460

Reply 466 of 616, by H3nrik V!

User metadata
Rank l33t
Rank
l33t
nd22 wrote on 2026-09-22, 06:40:

I have already shown my 3 AV8 in this post: Re: Battle of the platforms: socket 939!
I do not have the full package of this board but I have 3 guru clock version 1, 4 version 2 and no model 3 which is exceedingly rare:

Gotta love that Reset CMOS button under the nuclear power symbol. Pretty much signals "use with caution" 😎

If it's dual it's kind of cool ... 😎

--- GA586DX --- P2B-DS --- BP6 ---

Please use the "quote" option if asking questions to what I write - it will really up the chances of me noticing 😀

Reply 467 of 616, by marxveix

User metadata
Rank Oldbie
Rank
Oldbie

Socket754/Socket939 combo boards have both sockets, no upgrade board needed here, how many these two different sockets at one motherboard exist? https://www.asrock.com/mb/ULi/K8%20Combo-Z/

Best ATi Rage3 drivers for 3DCIF / Direct3D / OpenGL / GLUT / DVD : ATi RagePro drivers and software
33+MiniGL / OpenGL Win 9x dll files for all ATi-Rage3 based cards : ATi RagePro OpenGL files

Reply 468 of 616, by nd22

User metadata
Rank l33t
Rank
l33t

That must be the only one. Asrock was on the wild side back than, it put out some really crazy designs. Unfortunately it uses the uli m1689 chipset and that means AGP.

Reply 469 of 616, by marxveix

User metadata
Rank Oldbie
Rank
Oldbie
nd22 wrote on 2026-09-25, 18:46:

That must be the only one. Asrock was on the wild side back than, it put out some really crazy designs. Unfortunately it uses the uli m1689 chipset and that means AGP.

Asrock p4 version also available for intel with s478 and s775 in one board. S754 upgrade version i have seen, but 2in1 right away was first time.

Best ATi Rage3 drivers for 3DCIF / Direct3D / OpenGL / GLUT / DVD : ATi RagePro drivers and software
33+MiniGL / OpenGL Win 9x dll files for all ATi-Rage3 based cards : ATi RagePro OpenGL files

Reply 470 of 616, by AlexZ

User metadata
Rank Oldbie
Rank
Oldbie

Abit AX8 is not the only board with tall caps below PCIe slot.

Gigabyte GA-K8NF-9-RH and GA-K8NF-9 (Rev. 2.x) have the same fault. Gigabyte GA-K8N Ultra-SLI (rev. 1.0) has one cap below PCIe slot and chipset heatsink in bad position so no fan can be attached and 2 SATA ports blocked.

Gigabyte GA-K8NF-9 (Rev. 1.x, lacks 5x HT) and Gigabyte GA-K8NF9 Ultra (Rev. 1.x and 2.x) are fine.

From Gigabyte, GA-K8NF9 Ultra is basically the only good option.

Pentium III 900E,ECS P6BXT-A+,384MB,GeForce FX 5600, Voodoo 2,Yamaha SM718
Turion 64 MT-40@2.4Ghz,Gigabyte GA-K8NE,2GB,GeForce GTX 275,Audigy 2ZS
Phenom II X4 965,Gigabyte GA-MA770-UD3,8GB,GeForce GTX 780
Vishera FX-8370,Asus 990FX,16GB,GeForce GTX 980 Ti

Reply 471 of 616, by nd22

User metadata
Rank l33t
Rank
l33t

I got it!! After 2 failures I finally found a no name pci-express riser card sitting on a shelf at a local shop that works!! And I did not even payed any cash for it!

Reply 472 of 616, by nd22

User metadata
Rank l33t
Rank
l33t

It works just fine, you can see the PCI-EXPRESS interface is 16X as it should be! It took me 2 weeks but i got GTX 285 working on Abit AX8!

Reply 473 of 616, by nd22

User metadata
Rank l33t
Rank
l33t

I finally managed to find some free time and test the mains and the reserves systems. Installing all these benchmarks and games on a 150gb WD raptor is quite difficult and because I wanted to have 2 fresh systems I reinstalled Windows XP on the biggest IDE drive I have: WD 500gb!
After reinstalling XP SP3, the benchmarks and games that I described here: Re: Battle of the platforms: socket 939!, I disabled indexing service, left everything else at default and started testing.
Because I used a 19 inch monitor in the beginning you will see some screenshots in 1280*1024 format.

Reply 474 of 616, by nd22

User metadata
Rank l33t
Rank
l33t

In order to be easier for everyone reading the topic the nforce4 system has the Zune theme and the VIA system has the default Luna theme. Also the order will always be:
1. nvidia nforce4
2. VIA K8T890

Reply 475 of 616, by nd22

User metadata
Rank l33t
Rank
l33t

Without further ado let's begin:
1. Aquamark3 is the very first DirectX9 benchmark ever released. While it is very tough on AGP cards, GTX 285 is actually bottlenecked by the Athlon 64 X2 in this particular benchmark.
Default settings first: 1024*768, no sound, no AA, AF 4x:
A. NFORCE4
B. K8T890
We are interested in the average FPS, not the score! Screenshots with detailed results for anyone who wants to replicate the tests. Please be aware the msi afterbuner and fraps are always running and recording the framerate!

Last edited by nd22 on 2026-10-15, 17:23. Edited 1 time in total.

Reply 476 of 616, by nd22

User metadata
Rank l33t
Rank
l33t

2. Now we set the details to maximum and retest at the same 1024*768 resolution! Sound is also enabled:
A. NFORCE4
B. K8T890

Reply 477 of 616, by nd22

User metadata
Rank l33t
Rank
l33t

3. We increase the resolution to 1280*1024 and test without sound first:
A. NFORCE4
B. K8T890

Reply 478 of 616, by nd22

User metadata
Rank l33t
Rank
l33t

4. ... and with sound afterwards:
A. NFORCE4
B. K8T890

Reply 479 of 616, by nd22

User metadata
Rank l33t
Rank
l33t

5. nforce4 barely edges out the VIA system, nothing extraordinary ...yet!
We reached the final resolution: 1600*1200
A. NFORCE4
B. K8T890