VOGONS


First post, by dreamblaster

User metadata
Rank Oldbie
Rank
Oldbie

Coming soon (approx 1-2 months) :

An 8-bit ISA video card for IBM PC compatibles, with VGA output.
Similar to SerdaVision HDMI in feature set, but with analog VGA output, instead of HDMI output

see https://serdashop.com/products/serdavision-vga

The attachment serdavision_vga.jpg is no longer available
Last edited by dreamblaster on 2026-11-09, 19:31. Edited 1 time in total.

Visit http://www.serdashop.com for retro sound cards, video converters, ...
DreamBlaster X2, S2, S2P, HDD Clicker, ... many projects !
New X2GS TE & X16GS sound card : https://www.serdashop.com/X2GS-TE ,
Thanks for your support !

Reply 1 of 9, by Tiido

User metadata
Rank l33t
Rank
l33t

This looks fun. I also suggest giving option to output 15kHz signal, with Csync over Hsync pin so that it is possible to connect via SCART cable to old TVs and enjoy all the 200/240 line resolution games directly. you could interlace 400/480 modes or just use small font in those which probably looks better. This, I think will give this card a lot of extra appeal ~

I'm most curious about what chip is the U20.

T-04YBSC, a new YMF71x based sound card & Official VOGONS thread about it
Newly made 4MB 60ns 30pin SIMMs ~
mida sa loed ? nagunii aru ei saa 😜

Reply 2 of 9, by dreamblaster

User metadata
Rank Oldbie
Rank
Oldbie

Thanks !
15kHz with csync on the hsync pin should be possible, hardware can do it, it's a firmware thing. Will look into it later, first the card needs to be out.
U20 is a SN74ALVCH16721 : a 20-bit latch that takes all colour bits + syncs of a pixel at once, into resistor ladders (6 bits per colour, like real VGA).
The picture is from the KiCad design, which is not finished yet, still some parts to be added, like the DAC resistors.

Visit http://www.serdashop.com for retro sound cards, video converters, ...
DreamBlaster X2, S2, S2P, HDD Clicker, ... many projects !
New X2GS TE & X16GS sound card : https://www.serdashop.com/X2GS-TE ,
Thanks for your support !

Reply 3 of 9, by Tiido

User metadata
Rank l33t
Rank
l33t

That sounds good ~

Aha ok. I was thinking maybe it is a special DAC chip I have not yet seen before... There may be a need to have a buffer at the end of the resistors to avoid blurring image, especially with longer cables. THS7373 would be a good choice there, and you can run Csync through the 4th section to make it able to drive SCART composhit input directly too.

T-04YBSC, a new YMF71x based sound card & Official VOGONS thread about it
Newly made 4MB 60ns 30pin SIMMs ~
mida sa loed ? nagunii aru ei saa 😜

Reply 4 of 9, by dreamblaster

User metadata
Rank Oldbie
Rank
Oldbie

Thanks Tiido, good tip !
No special DAC chip, just a latch and resistor ladders, but they're set up for 75 ohm and 0.7V, same as the RAMDACs on the original VGA cards, which also drove the cable directly. So i expect a sharp picture.
I'll try the first boards with long cables and different monitors, and if it blurs i'll keep the THS7373 in mind for a next revision, the csync for SCART is a nice bonus then

I just ordered the prototypes, see screenshot :

The attachment serdavision_vga.jpg is no longer available

Visit http://www.serdashop.com for retro sound cards, video converters, ...
DreamBlaster X2, S2, S2P, HDD Clicker, ... many projects !
New X2GS TE & X16GS sound card : https://www.serdashop.com/X2GS-TE ,
Thanks for your support !

Reply 5 of 9, by jmarsh

User metadata
Rank Oldbie
Rank
Oldbie

Don't you need more resistors than that? Each input usually has two resistors each...

Reply 6 of 9, by dreamblaster

User metadata
Rank Oldbie
Rank
Oldbie

They're there, just small : the column of 0402 resistors right of the big chip 🙂
It's not an R-2R ladder (2 resistors per bit), but a binary weighted one : 1 resistor per bit, 330R, 680R, 1.37k, 2.74k, 5.62k, 11.3k (1%), plus a 130R shunt per colour to get the 75 ohm output impedance. So 6 bits per colour, like real VGA, with half the resistors.

The attachment serdavision_vga_closeup.jpg is no longer available

Visit http://www.serdashop.com for retro sound cards, video converters, ...
DreamBlaster X2, S2, S2P, HDD Clicker, ... many projects !
New X2GS TE & X16GS sound card : https://www.serdashop.com/X2GS-TE ,
Thanks for your support !

Reply 7 of 9, by Jo22

User metadata
Rank l33t++
Rank
l33t++

The SVGA modes look good, but I'd recommend to add 640x400@256c VBE (100h) and Paradise PVGA1C/WD90C00 support (for Win 2.03 256c SVGA driver). :)

"Time, it seems, doesn't flow. For some it's fast, for some it's slow.
In what to one race is no time at all, another race can rise and fall..." - The Minstrel

//My video channel//

Reply 8 of 9, by dreamblaster

User metadata
Rank Oldbie
Rank
Oldbie

Thanks !
640x400x256 (100h) is already in there, together with 101h, 102h and the hicolor 10Dh/10Eh.
Paradise support is a nice idea for the Win 2.x 256c driver, i'll put it on the list, it would be firmware only.

Visit http://www.serdashop.com for retro sound cards, video converters, ...
DreamBlaster X2, S2, S2P, HDD Clicker, ... many projects !
New X2GS TE & X16GS sound card : https://www.serdashop.com/X2GS-TE ,
Thanks for your support !

Reply 9 of 9, by Jo22

User metadata
Rank l33t++
Rank
l33t++

You're welcome. ^^ A high level approach is fine, I think. Thank you.
(As far as I know, the driver just sets a Paradise specific VGA video mode and expects a certain memory layout for 256c.)

Edit: There's something else that comes to mind..
Another positive side effect of that 256c Paradise driver is that is below 480 lines.
Because, resolutions closer to 350 or 400 line modes (Olivetti/AT&T etc) are more compatible with Windows 1.x/2.x software written especially with EGA (or Hercules) in mind.
The Windows 2.11 VGA driver uses a slightly reduced viewport because of this (it's 640x450 pels, I believe).
Edit: Might be related to non-Windows (ie, DOS) EGA applications.

"Time, it seems, doesn't flow. For some it's fast, for some it's slow.
In what to one race is no time at all, another race can rise and fall..." - The Minstrel

//My video channel//