VOGONS


Mitsubishi MP 386s Resurrection/Franken-rebuild

Topic actions

Reply 20 of 22, by ralphmaif

User metadata
Rank Newbie
Rank
Newbie

Did some pin mapping with a multimeter, and this is what I got.

The attachment pin map 01.jpg is no longer available

Is my research correct, though? I've read that the Picos are 3.3v and need the 5v signal stepped down with level shifters or they could fry.

Reply 21 of 22, by rasz_pl

User metadata
Rank l33t++
Rank
l33t++
ralphmaif wrote on 2026-11-14, 22:37:

Did some pin mapping with a multimeter, and this is what I got.

👍
J25 pins are numbered A1-25 B1-25 and I would stick to that
A1 = your 1
A2 = your 14
A25 = your 13
B1 = your 26
B2 = your 27
B25 = your 50

I would make a diagram in Kicad to keep track of everything
So far Im guessing B16 is some sort of clock (3.8V). Im surprised so many lines read on your meter read at full voltage, kinda worried actually that interface might need some magical unlocking?, we will see once you connect picos (or have oscilloscope and probe around for activity).

ralphmaif wrote on 2026-11-14, 22:37:

Is my research correct, though? I've read that the Picos are 3.3v and need the 5v signal stepped down with level shifters or they could fry.

pico1 is up to 5.5V guaranteed, afaik earliest pico2 were only up to 5V, current ones are all 5.5V. Industry standard for 5V tolerant is ~10% aka 5.5V. At 5$ I wouldnt worry too much, if pisos fry you can get more, still cheaper than building buffers for it.

https://github.com/piersfinlayson/one-rom/blo … LTAGE-LEVELS.md shows " all pins other than the RP2350 ADC inputs (see the note above) are fully 5v tolerant (up to 5.5V)" aka dont use GPIO26-29 aka Chan21-23. Thats loss of 6 sniffing channels so might be worth soldering one 74HC4050 (too slow) 74LVC244 powered from Pico 3.3V to translate just those 6 IOs down to 3.3V. But since there are 13 confirmed grounds you wont need more than 40 channels so can simply skip Chan21-23 on picos.

This is why I asked you to measure voltage on every pin of that connector 😀 If your PC PSU gives out way more than 5V it might be worth experimenting with very small resistors in line with Pico inputs. Dont see anything above 5.08 and one of those pins is bound to be Vcc (you didnt find direct conenction?) and since nothing can go over VCC we are safe across the board.

This is the only thing one might worry about https://retrosix.wiki/wiki/digital-logic-levels but as you can see logic levels line up pretty well between 5V TTL and 3.3V cmos = picos should have zero problem distinguishing logic levels with nothing in between

https://github.com/raszpl/sigrok-disk FM/MFM/RLL decoder
https://github.com/raszpl/FIC-486-GAC-2-Cache-Module (AT&T Globalyst)
https://github.com/raszpl/386RC-16 ram board
https://github.com/raszpl/Zenith_ZBIOS Zenith Z-386 MFM-300 ZBIOS disassembly

Reply 22 of 22, by ralphmaif

User metadata
Rank Newbie
Rank
Newbie
rasz_pl wrote on 2026-11-15, 04:18:
:thumbsup: J25 pins are numbered A1-25 B1-25 and I would stick to that A1 = your 1 A2 = your 14 A25 = your 13 B1 = your 26 B2 = […]
Show full quote
ralphmaif wrote on 2026-11-14, 22:37:

Did some pin mapping with a multimeter, and this is what I got.

👍
J25 pins are numbered A1-25 B1-25 and I would stick to that
A1 = your 1
A2 = your 14
A25 = your 13
B1 = your 26
B2 = your 27
B25 = your 50

I would make a diagram in Kicad to keep track of everything
So far Im guessing B16 is some sort of clock (3.8V). Im surprised so many lines read on your meter read at full voltage, kinda worried actually that interface might need some magical unlocking?, we will see once you connect picos (or have oscilloscope and probe around for activity).

ralphmaif wrote on 2026-11-14, 22:37:

Is my research correct, though? I've read that the Picos are 3.3v and need the 5v signal stepped down with level shifters or they could fry.

pico1 is up to 5.5V guaranteed, afaik earliest pico2 were only up to 5V, current ones are all 5.5V. Industry standard for 5V tolerant is ~10% aka 5.5V. At 5$ I wouldnt worry too much, if pisos fry you can get more, still cheaper than building buffers for it.

https://github.com/piersfinlayson/one-rom/blo … LTAGE-LEVELS.md shows " all pins other than the RP2350 ADC inputs (see the note above) are fully 5v tolerant (up to 5.5V)" aka dont use GPIO26-29 aka Chan21-23. Thats loss of 6 sniffing channels so might be worth soldering one 74HC4050 (too slow) 74LVC244 powered from Pico 3.3V to translate just those 6 IOs down to 3.3V. But since there are 13 confirmed grounds you wont need more than 40 channels so can simply skip Chan21-23 on picos.

This is why I asked you to measure voltage on every pin of that connector 😀 If your PC PSU gives out way more than 5V it might be worth experimenting with very small resistors in line with Pico inputs. Dont see anything above 5.08 and one of those pins is bound to be Vcc (you didnt find direct conenction?) and since nothing can go over VCC we are safe across the board.

This is the only thing one might worry about https://retrosix.wiki/wiki/digital-logic-levels but as you can see logic levels line up pretty well between 5V TTL and 3.3V cmos = picos should have zero problem distinguishing logic levels with nothing in between

Copy that, and thanks for the clarity. Updated the map to the J25 spec:

The attachment pin map 01.jpg is no longer available

I have the wires and breakout boards on order and should see them arrive sometime in the next week or so.