VOGONS


Reply 2020 of 2028, by rasz_pl

User metadata
Rank l33t++
Rank
l33t++

>enough spare GPIOs

$1 RP2350B 48 IOs. Its actually more cost effective to slap two RP2350 chips with one 100% dedicated to ISA IO than use 74x logic IO extenders.

>require extra level shifters

You shouldnt need any level shifters to begin with. Picos are 5.5V tolerant just like the level shifters used currently, its placebo now.

https://github.com/raszpl/sigrok-disk FM/MFM/RLL decoder
https://github.com/raszpl/FIC-486-GAC-2-Cache-Module (AT&T Globalyst)
https://github.com/raszpl/386RC-16 ram board
https://github.com/raszpl/Zenith_ZBIOS Zenith Z-386 MFM-300 ZBIOS disassembly

Reply 2021 of 2028, by jmarsh

User metadata
Rank Oldbie
Rank
Oldbie
rasz_pl wrote on Yesterday, 23:20:

You shouldnt need any level shifters to begin with. Picos are 5.5V tolerant just like the level shifters used currently, its placebo now.

No it isn't. It's only "5v tolerant" if the chip is fully powered - meaning the bus has to be isolated until the startup sequence is complete = external circuitry is still required. This is no different from the 2040.

Reply 2022 of 2028, by rasz_pl

User metadata
Rank l33t++
Rank
l33t++
jmarsh wrote on Today, 00:29:

No it isn't. It's only "5v tolerant" if the chip is fully powered - meaning the bus has to be isolated until the startup sequence is complete = external circuitry is still required. This is no different from the 2040.

14.9.1 (Absolute Maximum Ratings) shows
IOVDD=0 tolerance 3.63V
IOVDD=2.5V tolerance 4.2V
IOVDD=3.3V tolerance 5.5V
With linear reg dropout of 1.1V you are always above that margin. At the moment ISA 5V rail rises to 3.6V into linear reg you are already powering IOVDD with 2.6V giving you 1V margin for rise times.

Of course outputs still need buffers, but thats because of ISA bus loading.

https://github.com/raszpl/sigrok-disk FM/MFM/RLL decoder
https://github.com/raszpl/FIC-486-GAC-2-Cache-Module (AT&T Globalyst)
https://github.com/raszpl/386RC-16 ram board
https://github.com/raszpl/Zenith_ZBIOS Zenith Z-386 MFM-300 ZBIOS disassembly

Reply 2023 of 2028, by crusher

User metadata
Rank Member
Rank
Member
NeoG_ wrote on Yesterday, 07:16:
crusher wrote on Yesterday, 07:01:

An enhanced PicoGUS with MT32 (MUNT) functionality would just be a dream.
And if it can handle GM/.sf2 soundfonts (via FluidSynth?) as well this would be the ultimate killer card!!!

You can have that now if you add a wavetable-pi to the card's wavetable header

I know. But not having to add a daughterboard would be absolutely brilliant.

Reply 2024 of 2028, by Damiano.78

User metadata
Rank Newbie
Rank
Newbie

Wow, congratulations on your skills! I'm glad that you too would like to have the possibility to switch IRQ and DMA without having to physically put your hand on a new PicoGUS... Gold!

I agree too...the top of the top would be to have all the various MT-32 emulations etc... on board on the PicoGUS Gold, without having to buy an additional daughterboard with another RP on board...

Reply 2025 of 2028, by theelf

User metadata
Rank Oldbie
Rank
Oldbie
theelf wrote on 2026-11-08, 17:53:

Hi, any ideas this can be solved? https://github.com/polpo/picogus/issues/149

it happen all time, and it is becoming a real problem to using my system properly

Hi guys, answer to myself

Like i said before I have this problem with the PicoGUS CD emulation and was very annoying me. I do pgusinit /cdload 51, dir d: ok, then pgusinit /cdload 52, dir d:... and it shows me the files of 51!! pgusinit says the 52 is loaded, no error nothing. If I wait some seconds and try again, then it works.

So first I think is the PicoGUS firmware, but no. I installed the toolkit in a modern PC, compile, but realize firmware loads the new image fine and says the disc changed.

The problem was same with MSCDEX and SHSUCDX, i tested mscdex from dos 6.22 and pcdos 7. But lucky SHSUCDX have source code, so looking there I find the reason and the fix. It only ask the CD driver "hey, the disc changed?" if it pass around 7 seconds (128 ticks) since the last time you touch the drive. If you change the image and go to the drive before that, it gives you the old directory from the cache.

What I modified in shsucdx.nsm:

when you do directory stuff (FindFirst, Open, ChDir, GetAttr, GetSpace) now it always ask the driver for media change. It only drops the cache if the driver says "changed". File reads, FindNext and the MSCDEX calls (games reading raw sectors etc) still use the 7 seconds, so nothing goes slower.
New option /T:n for the timeout in seconds (0-99). Default still around 7 seconds. /T:0 = check every time. You can change it also when SHSUCDX is already loaded, butt at least for now, work fine with default in my 286 now

In the zip you have full source and two builds: SHCDX86.COM (8086/286) and SHSUCDX.COM (386). Compiled with NASM. All credit to Jason Hood for SHSUCDX (https://github.com/adoxa/shsucd), I only touch a little thing.

Also one idea for pgusinit, after a good /cdload or /cdloadname, pgusinit can send an IOCTL "media changed" (INT 2Fh AX=1510h) to the CD drives. SHSUCDX drops the cache immediately when it receive this, so people with normal SHSUCDX no need any patch. With MSCDEX I dont know if it works the same, need to test.

PicoGUS issue: https://github.com/polpo/picogus/issues/149

greetings!

The attachment shsucd-master.zip is no longer available

Reply 2026 of 2028, by NeoG_

User metadata
Rank Oldbie
Rank
Oldbie

I wonder if the behaviour is different in DOS7? I am able to see updated directory contents immediately after changing disc images with MSCDEX so disc change messaging must be working in some capacity

I wonder if there is a TSR or overlay you like to run which could be interfering with IOCTL?

98/DOS Rig: BabyAT AladdinV, K6-2+/550, V3 2000, 128MB PC100, 20GB HDD, 128GB SD2IDE, SB Live!, SB16-SCSI, PicoGUS, WP32 McCake, iNFRA CD, ZIP100
XP Rig: Lian Li PC-10 ATX, Gigabyte X38-DQ6, Core2Duo E6850, ATi HD5870, 2GB DDR2, 2TB HDD, X-Fi XtremeGamer

Reply 2027 of 2028, by theelf

User metadata
Rank Oldbie
Rank
Oldbie
NeoG_ wrote on Today, 11:59:

I wonder if the behaviour is different in DOS7? I am able to see updated directory contents immediately after changing disc images with MSCDEX so disc change messaging must be working in some capacity

I wonder if there is a TSR or overlay you like to run which could be interfering with IOCTL?

Hi, about TSR, no, i dont have any, and one of first test was removeee all drivers, like mouse, etc tried different himem.sys neither work

Thats why i decide to spend this weekend on this, because it was VERY nasty problem to me, almost every time i need to change CD, need to do a reset! even lend a laptop with win10 from my brother, installed pi pico sdk etc and compiled firmware thinking the bug can be there

for me is solved, hope if someone have similar problem can help

Reply 2028 of 2028, by theelf

User metadata
Rank Oldbie
Rank
Oldbie
polpo wrote:

...

WOW!!! I want to say THANK YOU for the latest beta firmware with Creative ADPCM support!!!! Thanks a lot!

The only reason I kept my SB16 was this: I have a VOC player in my shell and I love playing my music with no CPU use... jeje

Thanks! Great work!