VOGONS


First post, by Ozzuneoj

User metadata
Rank l33t
Rank
l33t

I have been struggling with this for years, but one of my test benches consists of two desks that are standing end-to-end, with the VGA monitor at one end and the computer being tested at the other end. To accommodate the rest of the stuff on the bench this is just how it has to be, with the wires routed out of the way behind things. Frustratingly, this means that the VGA cable has hardly any slack unless the computer is in exactly the right position... and if I'm just testing a motherboard setting out on the desk it can be pretty finicky to get everything oriented just right for the VGA cable to reach.

The cable I'm using now is one of those big fat black or gray VGA cables with the ridges that run the length of the cable (you've probably seen them). It's around 6 feet long and it is the longest one in my collection that is of this heavy duty type. I can't find any markings on this particular one, but another cable I have that has similar construction (but shorter) says the following on the cable:
TTL (brand) Style 2919 30v 80C HI-RES 75 OHM Low Attenuation A/V Coax High Frequency Series 1081359

At some point I picked up a 10ft Belkin branded cable with a built in audio cable (looks like this one), and I just tested that and there is a noticeable drop in clarity using a 6800GT's VGA port connected to a Dell 2001FP running at 1600x1200 at 60Hz. The Belkin cable says "Belkin Enterprise Series Cable: For Optimum Data Transfer" but the relevant points seem to be 28AWG, 60C, 30V. Sadly, the other cable does not say what AWG it is, so I can't compare those specs. The Belkin is physically thinner and less robust looking than the other, but that may just be the shielding.

I get a similar drop in clarity by using a cheap 1ft VGA extension cable added onto the end of the good cable that I have been using. So, my solution has been to just use that extension when high res clarity isn't an issue. For testing higher end cards I still need to go without it though to be sure the output is good and clear.

I'd like to just be done messing with this and get a 7+ foot VGA cable that doesn't sacrifice image clarity.

Does anyone know of anything like that?

I found some pictures of these C2G cables that say either 30AWG or 28AWG, 80C, 30V, and they seem to be pretty thick cables suitable for in-wall installation but see at least one review complaining of poor picture quality from multiple 10ft cables... so I don't know if they're actually as good as the beefy old ones from the days when very high res VGA was more common. I don't really need all 10 feet either.

EDIT: Also wanted to mention I have a bunch of KVM cables that I've accumulated but none are actually as good as the old dedicated VGA cables, plus they have PS/2 cables I don't need molded into them.

Now for some blitting from the back buffer.

Reply 1 of 18, by jmarsh

User metadata
Rank Oldbie
Rank
Oldbie

Simplest solution would be to use a VGA to HDMI adapter...

Reply 3 of 18, by Ozzuneoj

User metadata
Rank l33t
Rank
l33t
jmarsh wrote on 2026-11-19, 22:09:

Simplest solution would be to use a VGA to HDMI adapter...

I don't think that would help in this situation.

The whole point is to test VGA output from various cards (ISA to PCI-E cards) to a 4:3 VGA display to ensure that the cards don't have anything wrong with the VGA signal path. Ghosting, noise, clarity, etc. at high resolutions, and for older cards I need it to work predictably at various low res graphics and text modes (which is why I'm using a 2001FP).

jakethompson1 wrote on 2026-11-19, 22:17:

IEC has a lot of niche cables like that. I've bought MFM/RLL drive cable sets from them. I can't vouch for the VGA but there's one like you described in many lengths. https://iec.net/product/vga-monitor-cable-mal … igh-resolution/

Thanks! I looked at it briefly and they don't give much information about the cables, but I will keep those in mind as an option.

Now for some blitting from the back buffer.

Reply 4 of 18, by BitWrangler

User metadata
Rank l33t++
Rank
l33t++

I pick up these "Blue Diamond" brand cables for spares whenever I see them. I don't run 1600x1200 much though. These have seemed consistently in the top 10% of the cables that I have had, and any better ones I think have come with the monitor out of a CAD shop. Got coax signal wiring, ferrites each end, come in at least 6ft 10ft 25ft and 50ft maybe other sizes below above and between. Possibly the mylar shield is a disadvantage as it may crack up with repeated flexing, but woven shield will also tend to develop gaps or thin spots from bunching in similar conditions.

Unicorn herding operations are proceeding, but all the totes of hens teeth and barrels of rocking horse poop give them plenty of hiding spots.

Reply 5 of 18, by BitWrangler

User metadata
Rank l33t++
Rank
l33t++

Current production seem to be specified for up to 1920 x 1080 @ 60hz which is the top side of 2M pixels per frame when 1600x1200 is under it.. https://www.tomauri.com/products/premium-vga- … -15-pin-mm-10ft

Unicorn herding operations are proceeding, but all the totes of hens teeth and barrels of rocking horse poop give them plenty of hiding spots.

Reply 6 of 18, by darry

User metadata
Rank l33t++
Rank
l33t++

Maybe you could get an OSSC and use it to convert DVI/HDMI, without (or with) line multiplication, to more easily spot issues.

The VGA/RGB input is highly configurable.

Reply 7 of 18, by Ozzuneoj

User metadata
Rank l33t
Rank
l33t
BitWrangler wrote on 2026-11-19, 23:38:

I pick up these "Blue Diamond" brand cables for spares whenever I see them. I don't run 1600x1200 much though. These have seemed consistently in the top 10% of the cables that I have had, and any better ones I think have come with the monitor out of a CAD shop. Got coax signal wiring, ferrites each end, come in at least 6ft 10ft 25ft and 50ft maybe other sizes below above and between. Possibly the mylar shield is a disadvantage as it may crack up with repeated flexing, but woven shield will also tend to develop gaps or thin spots from bunching in similar conditions.

Thanks for the tip about Blue Diamond! It seems they aren't as common here in the US. I found someone selling one for a reasonable price but with $20 shipping, which is a bit nuts. They look a lot like the other good cables I've used, so maybe any cable that has that kind of construction will be built well enough to do the job.

darry wrote on Yesterday, 04:35:

Maybe you could get an OSSC and use it to convert DVI/HDMI, without (or with) line multiplication, to more easily spot issues.

The VGA/RGB input is highly configurable.

The OSSC is cool, but I really just need like 12 more inches of VGA cable without quality loss. I have a good selection of vintage displays, including a CRT on another desk which works great for cards that don't like any LCD. So I don't need to convert anything to HDMI to do what I've been doing.

I found a 10ft cable just now that looks really well built like the others I've used (similar to the Blue Diamond too), and it was around $8 shipped, brand new. I'll give that a shot and if that doesn't help I'll start looking at other solutions. I'd have preferred something a couple feet shorter to avoid any unneeded signal loss, but if it works I'll be happy.

Now for some blitting from the back buffer.

Reply 8 of 18, by BitWrangler

User metadata
Rank l33t++
Rank
l33t++
Ozzuneoj wrote on Yesterday, 04:47:
BitWrangler wrote on 2026-11-19, 23:38:

I pick up these "Blue Diamond" brand cables for spares whenever I see them. I don't run 1600x1200 much though. These have seemed consistently in the top 10% of the cables that I have had, and any better ones I think have come with the monitor out of a CAD shop. Got coax signal wiring, ferrites each end, come in at least 6ft 10ft 25ft and 50ft maybe other sizes below above and between. Possibly the mylar shield is a disadvantage as it may crack up with repeated flexing, but woven shield will also tend to develop gaps or thin spots from bunching in similar conditions.

Thanks for the tip about Blue Diamond! It seems they aren't as common here in the US. I found someone selling one for a reasonable price but with $20 shipping, which is a bit nuts. They look a lot like the other good cables I've used, so maybe any cable that has that kind of construction will be built well enough to do the job.

Up here they mostly seem to get to regional and small chains and larger mom and pops. Which has been kinda good for picking them up cheap when locations liquidate. Very "authentic" too, they've been around since at least late 90s.

Unicorn herding operations are proceeding, but all the totes of hens teeth and barrels of rocking horse poop give them plenty of hiding spots.

Reply 9 of 18, by jmarsh

User metadata
Rank Oldbie
Rank
Oldbie
BitWrangler wrote on 2026-11-19, 23:50:

Current production seem to be specified for up to 1920 x 1080 @ 60hz which is the top side of 2M pixels per frame when 1600x1200 is under it..

1600x1200 uses more bandwidth than 1920x1080 (162MHz vs 148.5MHz).

A 2001FP has DVI input - not sure why you're not willing to make use it. Converting to digital would be a much better indicator of whether any artifacts are being caused by the card rather than the run of cable.

Reply 10 of 18, by Ozzuneoj

User metadata
Rank l33t
Rank
l33t
jmarsh wrote on Yesterday, 06:25:
BitWrangler wrote on 2026-11-19, 23:50:

Current production seem to be specified for up to 1920 x 1080 @ 60hz which is the top side of 2M pixels per frame when 1600x1200 is under it..

1600x1200 uses more bandwidth than 1920x1080 (162MHz vs 148.5MHz).

A 2001FP has DVI input - not sure why you're not willing to make use it. Converting to digital would be a much better indicator of whether any artifacts are being caused by the card rather than the run of cable.

I already use the 2001FP's DVI input to test the DVI output of cards and have a DVI cable connected to that for that purpose.

If I'm testing hundreds of cards over the years (often after repairs), I really don't want to worry about digital conversion creating or hiding problems with any of them. If it happens once and takes me more than 5 minutes to realize it is a digital conversion problem, then it will be a net loss of time vs just replacing the VGA cable I have with a longer one (which I just ordered for $8).

I'm not sure why it would be hard to understand my desire to maintain an analog path to a display that is known to be very flexible and compatible with a large variety of VGA signals. I already have everything I need to do this and I've been using this test setup (admittedly with a different monitor until about 5 years ago) for over 10 years to test hundreds of cards. After moving things around I need another foot of good quality cable. Sticking an HDMI converter into the mix now, rather then just getting a longer cable, doesn't really make any sense for my purposes.

Now for some blitting from the back buffer.

Reply 11 of 18, by jmarsh

User metadata
Rank Oldbie
Rank
Oldbie
Ozzuneoj wrote on Yesterday, 07:09:

I'm not sure why it would be hard to understand my desire to maintain an analog path to a display that is known to be very flexible and compatible with a large variety of VGA signals.

That's not really true - the 2001FP is known to not support 70Hz, dropping one in seven frames because it can only output 60Hz - it's definitely not the ultimate testbench that you're making it out to be. But my main point would be: what do you think happens to the analog signal when it reaches the monitor? It doesn't get rendered using an analog process...
Every time you see ghosting, snow or any other sort of interference there will still be potential for the cable to be the cause, no matter how heavy duty it is.

Reply 12 of 18, by BitWrangler

User metadata
Rank l33t++
Rank
l33t++
jmarsh wrote on Yesterday, 06:25:
BitWrangler wrote on 2026-11-19, 23:50:

Current production seem to be specified for up to 1920 x 1080 @ 60hz which is the top side of 2M pixels per frame when 1600x1200 is under it..

1600x1200 uses more bandwidth than 1920x1080 (162MHz vs 148.5MHz).

A 2001FP has DVI input - not sure why you're not willing to make use it. Converting to digital would be a much better indicator of whether any artifacts are being caused by the card rather than the run of cable.

Ah shit, yeah the blanking intervals and porches add up to more than I spitballed in "qwik maff" in my head, I was going "bit under 150, vs bit over 150" the other way round. Anyway, it shouldn't brickwall a few Mhz away. Possibility they only quoted that res as it sounded more modern or "bigger" than 1600x1200. I think the type of cable should maintain signal integrity up over 200mhz but the attenuation will get bad over that.

Unicorn herding operations are proceeding, but all the totes of hens teeth and barrels of rocking horse poop give them plenty of hiding spots.

Reply 13 of 18, by BitWrangler

User metadata
Rank l33t++
Rank
l33t++

What I like about analog video testing is that you see stuff happen where digital would just drop and blackscreen. Though it's dependent on the willingness of your monitor to continue trying to display messed up pictures, early black or bluescreening that end isn't helpful.

Unicorn herding operations are proceeding, but all the totes of hens teeth and barrels of rocking horse poop give them plenty of hiding spots.

Reply 14 of 18, by jmarsh

User metadata
Rank Oldbie
Rank
Oldbie
BitWrangler wrote on Yesterday, 14:44:

What I like about analog video testing is that you see stuff happen where digital would just drop and blackscreen. Though it's dependent on the willingness of your monitor to continue trying to display messed up pictures, early black or bluescreening that end isn't helpful.

If it's a CRT that's using the sync signals to actually control the beam, sure. But any flat panel is going to be timing the syncs and fitting those to a known input profile, then using that to sample the colors at a fixed frequency. The only real differences with using DVI are that the pixel clock is actually provided, and the color signals are already digital so no sampling necessary.

Reply 15 of 18, by maxtherabbit

User metadata
Rank l33t
Rank
l33t

I have had extremely good results with the C2G cables you linked in the OP. They are made by legrand for professional installation and use 75R mini coax for the RGB lines as VGA cables should (and all did, once upon a time).

I use them both for my retro console matrix switch setup as well as with my 16 PC retro PC KVM. I have used them at resolutions up to 1080p without any signal degradation

Reply 16 of 18, by Ozzuneoj

User metadata
Rank l33t
Rank
l33t
jmarsh wrote on Yesterday, 13:46:
Ozzuneoj wrote on Yesterday, 07:09:

I'm not sure why it would be hard to understand my desire to maintain an analog path to a display that is known to be very flexible and compatible with a large variety of VGA signals.

That's not really true - the 2001FP is known to not support 70Hz, dropping one in seven frames because it can only output 60Hz - it's definitely not the ultimate testbench that you're making it out to be. But my main point would be: what do you think happens to the analog signal when it reaches the monitor? It doesn't get rendered using an analog process...
Every time you see ghosting, snow or any other sort of interference there will still be potential for the cable to be the cause, no matter how heavy duty it is.

Not sure what the deal is here, but I'm just trying to replace a VGA cable with a longer one. If I had the time, money or interest in replacing or upgrading devices on my test bench and then dealing with all the quirks of a more complex setup, I would research possible solutions, including posting about it here and asking for advice. That isn't what this thread is about, however.

I have answers for most of what you're saying, but given that you're only acknowledging one sentence out of each post I make I'm not really interested in taking more time to justify my use of a display setup that I already own and that has worked well for my needs for several years.

Besides, if the 2001FP craps out on me (which it likely will at some point in the not too distant future), I will most likely just drop in some other LCD monitor that I already have. If needed, I'll use my CRT for testing things that the LCD isn't capable of testing. That's what I did before I set up the (free) 2001FP for testing 1600x1200. I just prefer not to extensively run my CRT if I don't have to because of wear, heat, power and the fact that I don't have a good place for it on my main bench, so it's on a different desk.

OR... maybe, at that time, I will make a thread asking for advice on how to rework my test setup. 😮

Last edited by Ozzuneoj on 2026-11-21, 06:03. Edited 1 time in total.

Now for some blitting from the back buffer.

Reply 17 of 18, by jakethompson1

User metadata
Rank l33t
Rank
l33t
jmarsh wrote on Yesterday, 13:46:

That's not really true - the 2001FP is known to not support 70Hz, dropping one in seven frames because it can only output 60Hz - it's definitely not the ultimate testbench that you're making it out to be. But my main point would be: what do you think happens to the analog signal when it reaches the monitor? It doesn't get rendered using an analog process...
Every time you see ghosting, snow or any other sort of interference there will still be potential for the cable to be the cause, no matter how heavy duty it is.

Is there a way to immediately know whether an LCD does this frame-dropping? For example, would motion in Commander Keen be glitchy or otherwise noticeably un-smooth?

I always hear about this, but don't think I have ever experienced it, and I don't see how I would have magically selected "good" LCDs that do 70 Hz.

Reply 18 of 18, by jmarsh

User metadata
Rank Oldbie
Rank
Oldbie
jakethompson1 wrote on Today, 04:57:

Is there a way to immediately know whether an LCD does this frame-dropping? For example, would motion in Commander Keen be glitchy or otherwise noticeably un-smooth?

I always hear about this, but don't think I have ever experienced it, and I don't see how I would have magically selected "good" LCDs that do 70 Hz.

70HZ.EXE, or crowdsourcing info on "how does your LCD display treat 70Hz video modes?"
It's an app that shows numbers 0-6 each on consecutive frames, so if a monitor is only showing 6 out of every 7 frames one of the numbers will be missing.