First post, by kingcake
- Rank
- Oldbie
That PSU is a rebranded FSP (Fortron-Source Power) unit so you're safe.
"Enter at your own peril, past the bolted door..."
Main PC: i5 3470, GB B75M-D3H, 16GB RAM, 2x1TB
98SE : P3 650, Soyo SY-6BA+IV, 384MB RAM, 80GB
I'm looking forward in seeing some benchmarks on this setup. Maybe try Phil's DOS benchmark pack, including the following (with and without turbo mode enabled) :
Navrátil System Information
Norton System Information 8.0
Landmark Speedtest 2.0 & 6.0
Doom 1 timedemo 3
3D Bench
PC Player benchmark
Just check that L1 cache is enabled
jesolo wrote on 2020-07-17, 20:04:I'm looking forward in seeing some benchmarks on this setup. Maybe try Phil's DOS benchmark pack, including the following (with […]
I'm looking forward in seeing some benchmarks on this setup. Maybe try Phil's DOS benchmark pack, including the following (with and without turbo mode enabled) :
Navrátil System Information
Norton System Information 8.0
Landmark Speedtest 2.0 & 6.0
Doom 1 timedemo 3
3D Bench
PC Player benchmarkJust check that L1 cache is enabled
will do!
I was recently given the same mobo but with 25mhz cpu and no daewoo logo. Do you have the manual for it? I have decoded the jumpers except two of them...
It's a nice little mobo but still hovers at good 386dx40 speeds, cpu benchmarks will be high but real performance like 3dbench or doom/wolfenstein fps will show the truth 😀
Isn't this board an Elite Group WH 386SX?
https://stason.org/TULARC/pc/motherboards/E/E … 6-WH-386SX.html
"Will the highways on the internets become more few?" -Gee Dubya
V'Ger XT|Upgraded AT|Ultimate 386|Super VL/EISA 486|SMP VL/EISA Pentium
Anonymous Coward wrote on 2020-07-18, 09:04:Isn't this board an Elite Group WH 386SX?
https://stason.org/TULARC/pc/motherboards/E/E … 6-WH-386SX.html
Not exactly there is for example a JP9 and there is a verified jumper to select if your RAM has parity or not - the WH386SX mobo has no jumper for this.
They are very similar, maybe the 486slc mobo is optimized for this cpu or something , maybe the -D at the end of the model marks the difference
I propose the "-D" stands for Daewoo.
"Will the highways on the internets become more few?" -Gee Dubya
V'Ger XT|Upgraded AT|Ultimate 386|Super VL/EISA 486|SMP VL/EISA Pentium
Anonymous Coward wrote on 2020-07-18, 11:20:I propose the "-D" stands for Daewoo.
🤣
sadly no:
Then it will forever remain a mystery, unless the answer is hidden in the ECS archives somewhere. Maybe the waybackmachine can turn something up.
"Will the highways on the internets become more few?" -Gee Dubya
V'Ger XT|Upgraded AT|Ultimate 386|Super VL/EISA 486|SMP VL/EISA Pentium
Anonymous Coward wrote on 2020-07-18, 09:04:Isn't this board an Elite Group WH 386SX?
https://stason.org/TULARC/pc/motherboards/E/E … 6-WH-386SX.html
interesting
I propose the "-D" stands for Daewoo.
🤣
Got my ATX --> AT harness today so I can continue building
Going to use this Aztech labs Sound Galaxy sound card. It has good SB and Adlib compat thanks to a real Yamaha OPL chip. More importantly, it features a proprietary controller connector for matsushita/panasonic cd-rom drives...
which i'm using. it's a 2x panasonic/matsushita with proprietary interface.