I know what you mean appiah. I rarely buy monitors because of things like this. It is very hard to ship them, but... man, people have to know what a package goes through... right??

Got my refund for it already. But wow... all I can do is shake my head.

This is probably a stupid question, but is anything else likely to use the same tube as this? Is there any hope of replacing this 13" Trinitron tube from 1988?

Ozzuneoj wrote on 2021-03-16, 18:22:

I know what you mean appiah. I rarely buy monitors because of things like this. It is very hard to ship them, but... man, people have to know what a package goes through... right??

Got my refund for it already. But wow... all I can do is shake my head.

This is probably a stupid question, but is anything else likely to use the same tube as this? Is there any hope of replacing this 13" Trinitron tube from 1988?

I just looked that up before, the CPD-1404 apparently uses the same tube but that is probably equally rare, there might be others.
there might also be a few with "compatible" tubes idk

imi wrote on 2021-03-16, 18:27:

Ozzuneoj wrote on 2021-03-16, 18:22:

I know what you mean appiah. I rarely buy monitors because of things like this. It is very hard to ship them, but... man, people have to know what a package goes through... right??

Got my refund for it already. But wow... all I can do is shake my head.

This is probably a stupid question, but is anything else likely to use the same tube as this? Is there any hope of replacing this 13" Trinitron tube from 1988?

I just looked that up before, the CPD-1404 apparently uses the same tube but that is probably equally rare, there might be others.
there might also be a few with "compatible" tubes idk

How did you find that they use the same tube? Just curious.

just looking through service manuals, the tube model is: M34JNQ15X

snagged this under appreciated card. Because its rare.

EVGA 7900 GTO, not actual card. but looks like this one.

Basically identicle to a 7900 GTX but with underclocked fast 1.1ns Samsung BJ11 GDDR3 performance is between a 7800GTX and a 7900GTX and above a 7950 GT

Plan to put it in my 915 chipset build.

Nice find warlord. I had a 7950 gt back in the day and I always wanted a 7900gto. Have you received the 1080ti you bought yet?

Na, you were right he was a scammer, but I got a full refund, so no biggie.

All good these things happen and eBay generally refunds you so it was worth trying. What card did they send you?

China scammer never sent me anything, just took the money and ran.

Even better than a fake card. I cant wait till the supply of graphics cards normalizes and the price come back down to earth.

Bit different - Another random purchase from eBay for just a few pounds.

It's an IBM/ISS Proventia MX1004 firewall - I'm going to try and upgrade it as much as possible and run Sophos XG firewall on it.

I believe it's a Celeron 600Mhz or something inside with a normal looking 2.5" hard drive according to this picture I found.

SteveC wrote on 2021-03-16, 20:31:

Bit different - Another random purchase from eBay for just a few pounds. mx1004.PNG […]
Show full quote

Bit different - Another random purchase from eBay for just a few pounds.
mx1004.PNG

It's an IBM/ISS Proventia MX1004 firewall - I'm going to try and upgrade it as much as possible and run Sophos XG firewall on it.

I believe it's a Celeron 600Mhz or something inside with a normal looking 2.5" hard drive according to this picture I found.

mx1004 2.PNG

I'm not at all familiar with older networking gear. What would you use that firewall for? Just to protect older machines? I can't imagine that a firewall from the 90s can keep up with modern loads. Does it have 100mbit ethernet at least or is the interface upgradeable to 1gbit?

Genuinely curious. 😀

Ozzuneoj wrote on 2021-03-16, 20:51:

SteveC wrote on 2021-03-16, 20:31:

Bit different - Another random purchase from eBay for just a few pounds. mx1004.PNG […]
Show full quote

Bit different - Another random purchase from eBay for just a few pounds.
mx1004.PNG

It's an IBM/ISS Proventia MX1004 firewall - I'm going to try and upgrade it as much as possible and run Sophos XG firewall on it.

I believe it's a Celeron 600Mhz or something inside with a normal looking 2.5" hard drive according to this picture I found.

mx1004 2.PNG

I'm not at all familiar with older networking gear. What would you use that firewall for? Just to protect older machines? I can't imagine that a firewall from the 90s can keep up with modern loads. Does it have 100mbit ethernet at least or is the interface upgradeable to 1gbit?

Genuinely curious. 😀

I'll find out when I get it 😀 There are 4 gig ethernet interfaces so I'm hoping it can be useful. I'm using an old IGEL Thin client at the moment but it's a bit of a hack job.
I have a couple different networks at home e.g. servers, few different WiFis (like one locked down that my daugher's iPad is on). I host my own email etc at home too so I need something to protect the servers from the outside world.

A new thing with some old things.

Got myself a Radeon X1900 XTX

Yesterday, I got an ASUS P/I-P6NP5 rev. 1.41 mainboard with a PPro SL22T and 64 MB of EDO DRAM. It does come with a cooler which has a rather pragmatic approach to power the fan.

I do like the retentioning mechanism.

Looks like someone tried to scratch some material of the heat spreader. Probably a gold digger …😉

It will power my NT4.0 server.

Got myself an Arduino Nano clone and an Ethernet Shield, building a plipbox fo my A500 and some friends.

Bought an NEC V20 D70108C-8 for my Compaq Portable 1 9n eBay (being shipped at the moment).

CMB75 wrote on 2021-03-17, 06:51:

Yesterday, I got an ASUS P/I-P6NP5 rev. 1.41 mainboard with a PPro SL22T and 64 MB of EDO DRAM. It does come with a cooler which […]
Show full quote

Yesterday, I got an ASUS P/I-P6NP5 rev. 1.41 mainboard with a PPro SL22T and 64 MB of EDO DRAM. It does come with a cooler which has a rather pragmatic approach to power the fan.
PentiumPro-ASUS-P6NP5.jpg
I do like the retentioning mechanism.
PentiumPro-Socket8-Retention.jpg
Looks like someone tried to scratch some material of the heat spreader. Probably a gold digger …😉
PentiumPro-SL22T-scratches.jpg
It will power my NT4.0 server.

I've seen that before, even in systems that didn't have a gold cap CPU installed. Personally I think it's because one of the previous users had some trouble mounting the heatsink and moved it around somewhat, because I've seen it in systems that had been tossed onto the streets by the previous owners. Yours is scratched pretty badly though, but socket 8 used a new and somewhat different (and incompatible) cooling solution, so perhaps the shop owner had to figure out how to mount it properly first:P

someone probably tried cramming a So7 heatsink onto it and wondered why it won't fit ^^