SB16 PnP DOS7 setup CTCM error \ VOGONS

SB16 PnP DOS7 setup CTCM error

Topic actions

First post, by keropi

Posted on 2015-07-05, 16:52

keropi Offline

Rank l33t++

Rank: l33t++
Posts: 9802
Joined: 2003-09-08, 06:45
Location: Greece

Hiya!

I've been trying to setup a friend's SB16 CT2270 in a DOS 7x installation (DOS7 from 98SE but without any windows present at all).
Naturally I downloaded the CTCMBBS and SBBASIC driver packages. But the Creative PnP manager complains that I need to update settings in win98 - but there is no windows installed.
I remember a solution to this was found here but I can't find it atm 😢
Could a kind soul point me to the right direction?
TIA! 😊

🎵 🎧 ⏳ ⚡ SoundVision PRO,MK1869 , PCMIDI MPU , OrpheusII , Megacard and 🎶GoldLib soundcard website
💾💾💾 Looking for a full version of LIST ENHANCED 2.4y1 by V. Buerg, message me if you have it for sale! 💾💾💾

Reply 1 of 10, by wbc

Posted on 2015-07-05, 16:55

wbc Offline

Rank Member

Rank: Member
Posts: 199
Joined: 2015-03-14, 14:51
Location: Russia \ Omsk

As I remember changing "winbootdir" string in CTCU.EXE and CTCM.EXE (i.e. in HEX editor) should be sufficient.

--wbcbz7

Reply 2 of 10, by gerwin

Posted on 2015-07-05, 17:01

gerwin Offline

Rank l33t

Rank: l33t
Posts: 3313
Joined: 2004-05-07, 19:21
Location: NL

Or CTCM.EXE /t

--> ISA Soundcard Overview // Doom MBF 2.04 // SetMul

Reply 3 of 10, by keropi

Posted on 2015-07-05, 17:32

keropi Offline

Rank l33t++

Rank: l33t++
Posts: 9802
Joined: 2003-09-08, 06:45
Location: Greece

^ thank you both 😀
I will try the /t switch and if that fails I'll resort to hex editing 😀

Reply 4 of 10, by Cloudschatze

Posted on 2015-07-05, 17:54

Cloudschatze Offline

Rank Oldbie

Rank: Oldbie
Posts: 1441
Joined: 2005-06-16, 14:32

keropi wrote:
SB16 CT2270

This is not a PnP card; the use of CTCU/CTCM isn't necessary.

Reply 5 of 10, by keropi

Posted on 2015-07-05, 18:25

keropi Offline

Rank l33t++

Rank: l33t++
Posts: 9802
Joined: 2003-09-08, 06:45
Location: Greece

^ DIAGNOSE.EXE doesn't pick up the card at all.
LPT/Serial ports are disabled and needed resources assigned to ISA manually. If the card is not PnP at all then it might be DOA.

Reply 6 of 10, by PhilsComputerLab

Posted on 2015-07-05, 21:28

PhilsComputerLab Offline

Rank l33t++

Rank: l33t++
Posts: 6174
Joined: 2014-09-28, 03:33
Location: Western Australia

If it's not a PnP card, just run INSTALL (or was it SETUP) from SBBASIC folder. If you get an error about running it inside Windows, use SETVER. During the setup the resources can be configured if I remember correctly.

YouTube, Facebook, Website

Reply 7 of 10, by Sammy

Posted on 2015-07-05, 22:13

Sammy Offline

Rank Oldbie

Rank: Oldbie
Posts: 529
Joined: 2014-05-01, 20:34

Have the card jumpers for IRQ and DMA?

I have 2 SB16.. one with Jumpers , the other not.

The card without Jumpers need ctcm / ctcu / diganose to work.

Reply 8 of 10, by gerwin

Posted on 2015-07-05, 22:39

gerwin Offline

Rank l33t

Rank: l33t
Posts: 3313
Joined: 2004-05-07, 19:21
Location: NL

I noted this for the SB16 CT2290, which is based on the same CT1747 'OPL' controller:

Source - The card requires me to reserve an IRQ for legacy cards in the BIOS, and requires 'Diagnose /s' at every boot. CTCM does not detect it.

--> ISA Soundcard Overview // Doom MBF 2.04 // SetMul

Reply 9 of 10, by AlphaC

Posted on 2015-07-07, 07:33

AlphaC Offline

Rank Newbie

Rank: Newbie
Posts: 31
Joined: 2014-03-02, 07:30
Location: Norway

https://cloakedthargoid.wordpress.com/ctpnp-dos7/

Reply 10 of 10, by keropi

Posted on 2015-07-08, 11:46

keropi Offline

Rank l33t++

Rank: l33t++
Posts: 9802
Joined: 2003-09-08, 06:45
Location: Greece

thanks all for the help/tips !
I got the card working again after I cleaned it's ISA connector. It didn't look dirty though.
The card worked without the PnP manager , just like Cloudschatze said 😀

Go to top of page Go to top of page

Back to General Old Hardware