VOGONS


Reply 20 of 36, by moflihmoflih

User metadata
Rank Newbie
Rank
Newbie

ROM bios header pointer PLL pointer PLL table Crystal freq offset (value)
53008 0048h -> 10Ah(+30) ---> 13Ah 984h(+E) ---------> 992h (0B30)
57403 0048h -> 110h(+30) ---> 140h 930h(+E) ---------> 93Eh (0B86)
51804 0048h -> 108h(+30) ---> 138h 902h(+E) ---------> 910h (0B86)
51805 0048h -> 10Ah(+30) ---> 13Ah 988h(+E) ---------> 996h (0B86)
52910 0048h -> 112h(+30) ---> 142h 9A8h(+E) ---------> 9B6h (0B86)

are you sure this was a MAC board because the ROM you posted is a PC ROM!

these are all the roms of rage 128 i could find 3 of them are for AGP and 2 for PCI

RAGE128 GL 1999-02-03 PN 113-51804-1 01 AGP BK1-0-11-VR001-001-001-011 (32KB) 29.5MHz
RAGE128 GL 1999-03-19 PN 113-51805-1 01 AGP BK1-0-11-VR001-001-001-011 (64KB) 16MB 29.5MHz Xpert128 (TVout)
RAGE128 GL 1999-04-07 PN 113-52910-2 01 AGP BK1-0-14-VR001-001-001-014 (64KB) 32MB 29.5MHz AIW (tv tuner)

RAGE128 GL 1999-06-21 PN 113-57403-1 02 PCI BK1-0-13-VR001-001-001-013 (36KB) 32MB 29.5MHz
RAGE128 GL 1999-04-07 PN 113-53008-1 00 PCI BK1-0-12-VR001-001-001-012 (64KB) 16MB 28.6MHz AIW (tv tuner)

any way the rom you posted is 57403 this rom does not show any post screen if used with MAC board
the only one that works but has the clock issue is 53008 and it belongs to All-in-wonder card (so you get all the unwanted
tv stuff devices when using its ROM), by modding the the dot clock frequency it must be good to go.

which ATI rage 128 do you have, can you post a picture of the board and the flashing process
did the flash process went without any issues!

Reply 21 of 36, by Yoghoo

User metadata
Rank Oldbie
Rank
Oldbie
moflihmoflih wrote on 2026-08-11, 22:39:
ROM bios header pointer PLL pointer PLL table Crystal freq offset (value) 53008 0048h -> 10Ah(+30) ---> 13Ah 984h(+E […]
Show full quote

ROM bios header pointer PLL pointer PLL table Crystal freq offset (value)
53008 0048h -> 10Ah(+30) ---> 13Ah 984h(+E) ---------> 992h (0B30)
57403 0048h -> 110h(+30) ---> 140h 930h(+E) ---------> 93Eh (0B86)
51804 0048h -> 108h(+30) ---> 138h 902h(+E) ---------> 910h (0B86)
51805 0048h -> 10Ah(+30) ---> 13Ah 988h(+E) ---------> 996h (0B86)
52910 0048h -> 112h(+30) ---> 142h 9A8h(+E) ---------> 9B6h (0B86)

are you sure this was a MAC board because the ROM you posted is a PC ROM!

these are all the roms of rage 128 i could find 3 of them are for AGP and 2 for PCI

RAGE128 GL 1999-02-03 PN 113-51804-1 01 AGP BK1-0-11-VR001-001-001-011 (32KB) 29.5MHz
RAGE128 GL 1999-03-19 PN 113-51805-1 01 AGP BK1-0-11-VR001-001-001-011 (64KB) 16MB 29.5MHz Xpert128 (TVout)
RAGE128 GL 1999-04-07 PN 113-52910-2 01 AGP BK1-0-14-VR001-001-001-014 (64KB) 32MB 29.5MHz AIW (tv tuner)

RAGE128 GL 1999-06-21 PN 113-57403-1 02 PCI BK1-0-13-VR001-001-001-013 (36KB) 32MB 29.5MHz
RAGE128 GL 1999-04-07 PN 113-53008-1 00 PCI BK1-0-12-VR001-001-001-012 (64KB) 16MB 28.6MHz AIW (tv tuner)

any way the rom you posted is 57403 this rom does not show any post screen if used with MAC board
the only one that works but has the clock issue is 53008 and it belongs to All-in-wonder card (so you get all the unwanted
tv stuff devices when using its ROM), by modding the the dot clock frequency it must be good to go.

which ATI rage 128 do you have, can you post a picture of the board and the flashing process
did the flash process went without any issues!

Here are the photos. This was not the original bios. I tried an earlier uploaded bios but that only worked in Windows (when setting the Hz correctly). See earlier posts. Can't find the original bios atm but it was a MAC bios.

Reply 23 of 36, by Yoghoo

User metadata
Rank Oldbie
Rank
Oldbie
moflihmoflih wrote on 2026-08-12, 21:48:
ah i see that you have a 27Mhz crystal on this card, thats crazy how many values of this crystals were ATI using ! i adjusted th […]
Show full quote

ah i see that you have a 27Mhz crystal on this card, thats crazy how many values of this crystals were ATI using !
i adjusted the ROM accordingly
https://drive.google.com/file/d/1Bz8qknFhWhUv … ?usp=drive_link
give it a try now

Thanks! Will try it hopefully tomorrow.

Reply 24 of 36, by Yoghoo

User metadata
Rank Oldbie
Rank
Oldbie
moflihmoflih wrote on 2026-08-12, 21:48:
ah i see that you have a 27Mhz crystal on this card, thats crazy how many values of this crystals were ATI using ! i adjusted th […]
Show full quote

ah i see that you have a 27Mhz crystal on this card, thats crazy how many values of this crystals were ATI using !
i adjusted the ROM accordingly
https://drive.google.com/file/d/1Bz8qknFhWhUv … ?usp=drive_link
give it a try now

Tried it today but unfortunately there is no output at all. Flash was successful with ATI flash 1.6 (with -f option).

Reply 25 of 36, by moflihmoflih

User metadata
Rank Newbie
Rank
Newbie

ok now the question is
which rom, allowed you to post but had the out of synch issue ?
the one you flashed before the moded roms, did it allow you to post or no ?
if the ROM you uploaded the "57403" showed you a post
here is a moded version of it
https://drive.google.com/file/d/1sn2PwaNFqJn5 … iew?usp=sharing
give it a try

Reply 26 of 36, by Yoghoo

User metadata
Rank Oldbie
Rank
Oldbie
moflihmoflih wrote on 2026-08-13, 13:48:
ok now the question is which rom, allowed you to post but had the out of synch issue ? the one you flashed before the moded ro […]
Show full quote

ok now the question is
which rom, allowed you to post but had the out of synch issue ?
the one you flashed before the moded roms, did it allow you to post or no ?
if the ROM you uploaded the "57403" showed you a post
here is a moded version of it
https://drive.google.com/file/d/1sn2PwaNFqJn5 … iew?usp=sharing
give it a try

This version works great so far. Can see the boot screen, tried a couple of DOS games and Windows 98SE also works perfectly (3DMark 99).

Thanks!

Reply 27 of 36, by moflihmoflih

User metadata
Rank Newbie
Rank
Newbie
Yoghoo wrote on 2026-08-13, 14:35:
moflihmoflih wrote on 2026-08-13, 13:48:
ok now the question is which rom, allowed you to post but had the out of synch issue ? the one you flashed before the moded ro […]
Show full quote

ok now the question is
which rom, allowed you to post but had the out of synch issue ?
the one you flashed before the moded roms, did it allow you to post or no ?
if the ROM you uploaded the "57403" showed you a post
here is a moded version of it
https://drive.google.com/file/d/1sn2PwaNFqJn5 … iew?usp=sharing
give it a try

This version works great so far. Can see the boot screen, tried a couple of DOS games and Windows 98SE also works perfectly (3DMark 99).

Thanks!

Excellent 2 cards working up until now mine and yours 😁
this is mysterious, i need to uncover what's in the ROMs that prevent them from posting on one version of the card and not another
anyway enjoy.

Reply 28 of 36, by JAKra85

User metadata
Rank Member
Rank
Member

Hello Everyone,

Nice work! Lucky I found you! 😁
I am also thinking of something similar.

I have two cards, same chips and designed approximately at the same time if we consider the PCB PartNumber.

ATi Rage 128 Pro - AGP - 16 MB SDR (PN 109-63000-00) for Mac
Memory config: 8 x MT48LC1M16A1-7SE on 128 bit.

ATi Rage 128 Pro - AGP - 16 MB SGR (PN 109-63100-10) for PC
Memory config: 4 x Samsung K4G323222M-PC70, not tested yet. Not sure if 64 or 128bit memory.
I think it's 64bit, because on the backside there are traces for 4 additional memory chips for a total of 32MB.

I am not that skilled to edit the BIOS file, however I can get the files and I can use tools to flash new BIOSes.
Would you help me make the ATi Rage 128 Pro - 16 MB SDR for Mac boot on a PC? 😀

Both use 29,4 crystals.

Retro PC Gallery:
https://docs.google.com/document/d/1ara32t4rV … nU/edit?tab=t.0

Reply 29 of 36, by moflihmoflih

User metadata
Rank Newbie
Rank
Newbie
JAKra85 wrote on 2026-08-13, 19:09:
Hello Everyone, […]
Show full quote

Hello Everyone,

Nice work! Lucky I found you! 😁
I am also thinking of something similar.

I have two cards, same chips and designed approximately at the same time if we consider the PCB PartNumber.

ATi Rage 128 Pro - AGP - 16 MB SDR (PN 109-63000-00) for Mac
Memory config: 8 x MT48LC1M16A1-7SE on 128 bit.

ATi Rage 128 Pro - AGP - 16 MB SGR (PN 109-63100-10) for PC
Memory config: 4 x Samsung K4G323222M-PC70, not tested yet. Not sure if 64 or 128bit memory.
I think it's 64bit, because on the backside there are traces for 4 additional memory chips for a total of 32MB.

I am not that skilled to edit the BIOS file, however I can get the files and I can use tools to flash new BIOSes.
Would you help me make the ATi Rage 128 Pro - 16 MB SDR for Mac boot on a PC? 😀

Both use 29,4 crystals.

if they are they both have the same clock and almost the same part number, go ahead and slap that PC bios in your MAC and see what will happen !
for the memory configuration i wont bother, because in RAGE 128 bios ATI has a subroutine within it that checks the memory configuration and sets the RAM config registers accordingly
hope the rage 128 pro has the same thing.
if you have 4 of K4G323222M 512K*32bit*2banks means you have 128bit
use the file "Rage128progl_120-120mhz32mb128bit" (it has the P/N 133-63211-10) from this link "https://www.vgamuseum.info/index.php/componen … ti-rage-128-pro" change the file extension to ".ROM" if flash16 complains.

Reply 30 of 36, by 0brain

User metadata
Rank Newbie
Rank
Newbie

Hello everyone,

I got a basically free Mac Rage 109-63000-00 and really wanted a PC Rage with DVI (which exist, but are really rare apparently). To find a solution I went a bit overboard and collected 30 VBIOS, tested them and only then stumbled upon critical info: this thread and a review of a real PC DVI card 🤦

TL;DR: I got the mentioned card working, and DVI is fine too, so thanks for all the info/help.

Some details:

Getting the card to POST with a PC Video BIOS wasn't a problem, in my downloads I found 3 VBI files which worked somewhat. As it turns out, most Rage Pro 128 BIOS available on the web are using 29.5 MHz crystals like the Mac card. This thread enabled me to check the PLL table for confirmation and modify it on demand.

How the PLL table works is described in "RAGETM128 Software Development Guide Technical Reference Manual P/N: SDK-G04000 Rev 0.01" page 60 ff. and the table is detailed in "RAGE PRO and Derivatives Programmer’s Guide Technical Reference Manual P/N: PRG-215R3-00-10 Rev 1.0" page 296 ff.

This info enabled me to get other VBI files working by modifying the table and then using "ATI bios edit" to load the corrupted bios (ignoring the checksum) and saving a new file with corrected checksum.

Still I could not get the DVI to work. Even a VBI file from the original PC DVI card of the review did not work at all - the reviewer was nice enough to dump his vbios for me (thanks again for that!). I even put the crystal on my card into a socket and changed it for other ones without success...

Finally I suspected the Mac card had different hardware than the PC variant and started to compare pictures of both cards:

The Mac card seems to use a different DVI pinout than the PC variant, pins 23+24 are connected to two capacitors (or inductors?) on Mac but via wire links on PC.

Soldering wire links finally did the trick (I did not remove the big capacitors), I got DVI in BIOS, DOS and Windows, see pictures.

If someone wants the VBI files I collected from different sites please contact me, I'm not sure about attaching them here. The same goes for the ATI documentation, but these files are much easier to find on the internet (bitsavers etc.)

Reply 31 of 36, by esasoft

User metadata
Rank Newbie
Rank
Newbie
moflihmoflih wrote on 2026-08-11, 14:07:

if someone is interested i will do a post on this dissassembly.

Hi!
Please make a full ROM dissassebly guide for this card!

Reply 33 of 36, by RaVeNsClaw

User metadata
Rank Newbie
Rank
Newbie

I followed the instructions in this thread and successfuly converted a 109-63000-00 with AGP and DVI from Mac to PC.
I've used the bios file from Tweakstone in the previous post, ATiflash 1.6 and the hardware modification by 0brain.
Works like a charm. 😀

Some small notes:
- 0brain was right to leave the two “big capacitors” next to the DVI port (which are actually ferrites) on the board. Without them, the card experiences scaling issues in text mode.
- Do not flash a PCI Rage 128 BIOS onto an AGP card. You'll have to desolder the EEPROM, flash it, and solder it back on. Don't ask why I know that.
- The card doesn't need active cooling at 120/120 MHz. I put on a passive heatsink and used my thermal camera in the UT intro to monitor the temps. It never reached 55°C.

Reply 34 of 36, by marxveix

User metadata
Rank Oldbie
Rank
Oldbie
RaVeNsClaw wrote on 2026-11-13, 18:58:

Do not flash a PCI Rage 128 BIOS onto an AGP card. You'll have to desolder the EEPROM, flash it, and solder it back on. Don't ask why I know that.

Of cource its not good idea to flash PCI bios to AGP vga and i am no expert on this, but i have usually flashed bad vga flash back to normal with second (working) videocard.

Best ATi Rage3 drivers for 3DCIF / Direct3D / OpenGL / GLUT / DVD : ATi RagePro drivers and software
33+MiniGL / OpenGL Win 9x dll files for all ATi-Rage3 based cards : ATi RagePro OpenGL files

Reply 35 of 36, by RaVeNsClaw

User metadata
Rank Newbie
Rank
Newbie
marxveix wrote on 2026-11-13, 19:04:

Of cource its not good idea to flash PCI bios to AGP vga and i am no expert on this, but i have usually flashed bad vga flash back to normal with second (working) videocard.

I tried, but in this case the card wasn't detected anymore.
I got confused with the post by moflihmoflih, as the DVI cards also have a 29.4 MHz quarz and his testbench showed a AGP AND a PCI card.
I should have looked at the pictures more closely.

It wasn't bad though. The heat capacity of these simple circuit boards is so low that my cheap hot air station was more then sufficient to de- and resolder the EEPROM.
So to emphasize it again: The BIOS posted by moflihmoflih is for the PCI 109-57400-00, alias Rage ORION.
What a great name. 😉

Btw.: There are at least three different types of Rage 128 PCI cards for MAC :
109-57400-00 - RAGE ORION - 16MB:
https://drivers.amd.com/manuals/orion.pdf
https://videocardz.net/ati-rage-orion

109-57400-30 - XCLAIM VR 128 - 16MB:
https://drivers.amd.com/manuals/xclaimvr128.pdf
https://jp.mercari.com/item/m39095954682

109-57500-00 - NEXUS 128 - 32MB:
https://drivers.amd.com/manuals/nexus128.pdf
https://pc.watch.impress.co.jp/docs/article/990215/ati1.jpg

Reply 36 of 36, by Socket3

User metadata
Rank Oldbie
Rank
Oldbie
moflihmoflih wrote on 2026-08-11, 14:07:
hi guys i think that i have solved the issue short answer is : wrong "Dot Clock Reference Frequency" in the PCI roms which is = […]
Show full quote

hi guys
i think that i have solved the issue
short answer is : wrong "Dot Clock Reference Frequency" in the PCI roms which is = 28.6Mhz, while on the crystal onboard is 29.498Mhz 😀
find the 29Mhz moded rom here
https://drive.google.com/file/d/139u2tTwWMtxC … iew?usp=sharing

2 weeks of scouring the ATI RAGE 128 programmer reference guide, and disassembling the ROM (found PLL tables, bios header values.....) i was looking for why my (MAC to PC) card was showing 16MB instead of 32MB well later i discovered that the VBIOS is universal and that it tests all configuration starting from 32MB down to 4MB, and that my card is indeed a 16MB 😁 (didnt pay attention to rams installed i just followed what the net was saying).

anyway with the RAM size problem solved now i started tackling the "Signal Error" on LCDs and high end CRTs of this converted card

The attachment outofsync.JPG is no longer available

so while looking for a solution on the net i stumbled on this post, so you were just like me having the same issue, i kept reading until "Thermalwrong" gave the right suggestion the one clue that i needed
which is the "crytsal frequency" might not match!

so i quickly jumped to the disassembled code and in the PLL table i found:

The attachment dot clock freq.jpg is no longer available

and right there the frequency was 28.6Mhz and not 29.4Mhz !
so i changed the offsets as follows:
2948 -> 0B84h
0992h 30h -> 84h
0993h 0Bh -> 0Bh (unchanged)
NOTE: these offsets are not the same on all ROMs, you need to calculate these starting from header bios pointer which is at offset 0048h if someone is interested i will do a post on this dissassembly.
then i used the ATI bios editor by Alex Yakovlev to recalculate the Checksum (this ati rom uses a table checksum not a single byte checksum).
flashed it using ATI FLASH1.6 (it didnt work on my pentium 4 board but flashed fine on pentium 3 board )

The attachment DSC_1448.JPG is no longer available

and voila, now the out of sync problem is gone, forever .... well i need your feed back to make sure ...

The attachment DSC_1450.JPG is no longer available

note: (the moded rom goes from 64kb to 45KB which is due the ATI bios editor, but its the only way i found to correct the checksum)
Enjoy!

Thank you for the ROM!! I flashed it on one of my cards and the "out of range" warning went away. I see you based the rom off the ATi All In Wonder PCI card, as such it installs a bunch of junk devices the card's don't physically have. Any way of getting around that?