VOGONS


Reply 40 of 64, by AppleSauce

User metadata
Rank Oldbie
Rank
Oldbie

My issue is my retro setups rely heavily on crts , I'm currently in the process or repairing a nec multisync 1401 (the original) which has a failing flyback given its nearly 40 years old.

All my setups are kind of exotic in nature and rely on specific substitutes , and it was a pain to acquire all these monitors and price has only gone up since then , not to mention inflation and shipping going up because of external factors.

I've already had to do an number of other repairs , like the NEC already had a switch IC fail and had to repair that , the phillips screen needed a flyback swap and HOT swap.

In theory i could substitute the VGA based computers with LCDs or something , but i use Voodoo cards and those can be a be bit picky with what screen they work with.

The Amiga is trickier since it needs 15Khz horizontal scan which most screens don't do.

The Japanese Computers though are an totally different ballgame of pain in the ass , they need proper Multisyncs.

The X68000 is a bit easier than the Towns since it needs only 15khz and 31khz depending on the game you might need either.

But the FM Towns needs all three as the boot screen and text modes want 24khz.
As nice a nice bonus i managed to get the FM Towns monitor to connect to a Neo Geo AES with a XNEO-1 RGB/S adaptor made by Micomsoft.
So if that screen failed it would complicate stuff quite a bit with how i have things organised.

Also getting replacements parts for the 536 could be tricky since it was a Japan only monitor and it was kind proprietary to Towns Systems parts wise.
And although its secretly a low-middle range Sony Trinitron PVM inside (same tube as Sony PVM-1341) it could have a proprietary flyback so i don't know if it would be possible to acquire replacement parts which are getting more expensive and harder to source.

I do have an XRGB that i got for a backup solution for the Neo Geo but the image is a bit washed out ,then there's the other issue that a modern flat screen display might kill the aesthetics of the setup as well and look out of place.

That said if someone has a more reasonable setup than mine it should be possible to use OSSC devices and LCDs or OLED displays but i have painted myself into a pretty tricky corner over with all the weird edge cases I have to juggle with so I'm not really sure I've got a good solution for replacement for my given situation.

The attachment 20260906_125626.jpg is no longer available
The attachment 20260906_125824.jpg is no longer available
The attachment 20260906_125600.jpg is no longer available
The attachment 20260906_125549.jpg is no longer available

Reply 41 of 64, by pshipkov

User metadata
Rank l33t
Rank
l33t

A good, late, "high-end" CRT monitor is much better at handling analog video input compared to any LCD.
LCDs are built around digital video input (dvi, dp, ...) while nalog signal handling (vga, ega cga herc) is in the row "legacy support".
Makes a big difference when exploring wide range of isa/vlb graphics cards, video resolutions and refresh rates.

retro bits and bytes | DOS media library

Reply 42 of 64, by FullYes

User metadata
Rank Member
Rank
Member

Gosh I hate LCDs. I went from CRT to plasma to Oled for my main TV at home, I had to have a couple of LCDs for my main PC but got oled now there too

I’m using a Dell P2425 for my socket 7 and socket A systems (both connected to it, one via vga and one via dvi/hdmi) running dos/w98. It’s a 1920 x 1200 monitor so there are a lot of resolutions that have perfect pixel alignment in either fullscreen or 4:3 mode. (I don’t mind 320 x 200 or 640 x 400 in 16:10) And it has a refresh rate of 100Hz. All good you might be thinking but I don’t like the way it picks up ambient light reflections and the viewing angles aren’t great.

I was considering trying to get a dell 2007fpb, but these are coming up on 20 years old now, and, as they are well regarded, expensive.

What I think I want is a smallish (20”?) oled that can handle vga but has a high enough resolution that pixel alignment doesn’t matter

System 1: K6-3+ MS-5158 (430TX), Voodoo3, AWE64
System 2: Athlon XP-M 2800+ SL-75KAV (KT133A) Quadro FX 1000, Vibra 16
System 3: 775i65g E5800, FX5900XT, Audigy 2ZS
System 4: i7-2600k, P8P67-M, GTX 460

Reply 43 of 64, by SScorpio

User metadata
Rank Oldbie
Rank
Oldbie
AppleSauce wrote on 2026-09-06, 03:58:

That said if someone has a more reasonable setup than mine it should be possible to use OSSC devices and LCDs or OLED displays but i have painted myself into a pretty tricky corner over with all the weird edge cases I have to juggle with so I'm not really sure I've got a good solution for replacement for my given situation.

The OSSC was pretty much created to handle your situation. The YouTube channel Adrian's Digital Basement has all kinds of weird hardware and he makes heavy use of the OSSC.

The just released first batch sold out, but RetroTink just released the new 6X CE. Unlike the OSSC it has a frame buffer so it's able to do more with the signal than the clock adjustments the OSSC does. It has a "easy mode" button where it does some voodoo and is able to get figure out what the signal is and get a picture out of it. You can then tweak what it settled on to further dial in the settings, and even save them to a custom profile. You can have multiple custom profiles so you can switch systems you're using without needing to redo everything each time. It's limited to a max resolution of 1440p output, but paired with a good monitor it will look great. Or get an external HDMI -> VGA DAC and you can output to a normal VGA CRT.

Reply 44 of 64, by 65C02

User metadata
Rank Member
Rank
Member

Yes I have a CRT screen still. One of the black Dell 17" ones from 2003. I am posting (well trying to post) this from my Windows ME computer with that monitor. I hope this works 😀

Reply 45 of 64, by RetroPCCupboard

User metadata
Rank Oldbie
Rank
Oldbie

I have a 19" Sony Trinitron in use for my PCs. Sharing it between them with a KVM. I have two smaller non-Trinitron CRTs in the garage covered in dust covers as fallback options if the good screen breaks

Reply 46 of 64, by Brawndo

User metadata
Rank Member
Rank
Member

I currently have 4 CRT PC monitors: a 15" something or other standard VGA, a 17" Dell flat screen, a 19" Gateway flat screen, and a 21" Dell/Sony which I need to fix the whitewash issue on. I will never trade them for LCD as they are just not comparable. Also I have a few sets of the Act Labs PC light guns which require a CRT to function. I will continue to use them until they (or I) die.

I also have 4 CRT TVs for my old component DVD players and video game consoles: 2 Sony 36" Trinitron (one is a Wega), a 27" curved Trinitron, and 27" Panasonic flat screen. Due to space limitations, I am done acquiring CRTs, for now... Unless of course a deal comes up I can't refuse, like somebody giving away a Mitsubishi Diamondtron or a Lacie Electron blue, in which case of course I'll have the room.

Reply 47 of 64, by AlexZ

User metadata
Rank Oldbie
Rank
Oldbie
momaka wrote on 2026-09-05, 21:16:

What ticks me off more is when people try to run their old 17" beat-up CRT at 1280x1024. Not only is it the incorrect aspect ratio, but most 17" CRTs simply cannot display that high of a resolution and will always look pretty blurry. The cherry on top is that most also won't allow more than 60 Hz refresh rate (especially the cheaper ones), making for a flickery, blurry, and geometry-incorrect image. Ugh!

I have run into some games that don't support 1280x960, only 1280x1024 and due to the way refresh rate works in Windows XP it is easiest to just run it at 1280x1024@85Hz.

I have two CRTs
- 19" AOC 9GlrA
- 17" Samsung 757DFX - serves as backup

both are capable of 1600x1200@75Hz

The cheap CRT that can only do 60Hz at 1280x1024 are more for Windows 98 era and 1024x768 max.

Pentium III 900E,ECS P6BXT-A+,384MB,GeForce FX 5600, Voodoo 2,Yamaha SM718
Turion 64 MT-40@2.4Ghz,Gigabyte GA-K8NE,2GB,GeForce GTX 275,Audigy 2ZS
Phenom II X4 965,Gigabyte GA-MA770-UD3,8GB,GeForce GTX 780
Vishera FX-8370,Asus 990FX,16GB,GeForce GTX 980 Ti

Reply 48 of 64, by gaffa2002

User metadata
Rank Member
Rank
Member
momaka wrote on 2026-09-05, 23:04:

Sadly nothing I can find any information on anywhere.
Gonna have to be serviced by someone who's done CRTs and can do it without an SM. I probably can, but I'm unfortunately a little too far. Unless you consider uploading lots of pictures of the insides after taking it apart in order to attempt to repair it with the help from other people on the internet (which, as you stated, you have no interest in doing any repairing yourself), then not sure what else there is left to do.

Thanks for taking your time!
Here is the service manual for it (mine is the 562ns) in case you are curious, however I have no intention of fixing it for now. Maybe once I move somewhere larger and learn something about fixing monitors…
For now I’m staying with the shitty no-brand that at least works so my daughter can use it. It would be a great replacement if it wasn’t for the ugly ghosting 😔…

LO-RES, HI-FUN

Reply 49 of 64, by gaffa2002

User metadata
Rank Member
Rank
Member

I know double posting is not nice, but I have an update on the monitor diagnosis:
Today I tried turning it on, and I’ve got the expected power cycle issue. But I left it there for a moment power cycling and eventually it turned on! Sadly after some more time it turned off again and returned to the power cycle.
Does that indicate something more about what the problem could be?
Thanks in advance

LO-RES, HI-FUN

Reply 50 of 64, by rmay635703

User metadata
Rank l33t
Rank
l33t
gaffa2002 wrote on 2026-09-09, 11:38:
I know double posting is not nice, but I have an update on the monitor diagnosis: Today I tried turning it on, and I’ve got the […]
Show full quote

I know double posting is not nice, but I have an update on the monitor diagnosis:
Today I tried turning it on, and I’ve got the expected power cycle issue. But I left it there for a moment power cycling and eventually it turned on! Sadly after some more time it turned off again and returned to the power cycle.
Does that indicate something more about what the problem could be?
Thanks in advance

Should start a new post with the model and a description of the problem as you currently have a junk screen unless it’s fixed.

You have either a failing component in the power section or a failing component downstream drawing too much power, without a detailed visual inspection combined with probing suspect components for failure you aren’t going to get anywhere, unless your screen has a very well known failure point so you can throw parts at it.

Very common for folks to id and replace all caps (even diodes) blindly but that can turn out to be a big waste of time if it’s something more serious.

Reply 51 of 64, by gaffa2002

User metadata
Rank Member
Rank
Member
rmay635703 wrote on 2026-09-09, 17:32:
Should start a new post with the model and a description of the problem as you currently have a junk screen unless it’s fixed. […]
Show full quote
gaffa2002 wrote on 2026-09-09, 11:38:
I know double posting is not nice, but I have an update on the monitor diagnosis: Today I tried turning it on, and I’ve got the […]
Show full quote

I know double posting is not nice, but I have an update on the monitor diagnosis:
Today I tried turning it on, and I’ve got the expected power cycle issue. But I left it there for a moment power cycling and eventually it turned on! Sadly after some more time it turned off again and returned to the power cycle.
Does that indicate something more about what the problem could be?
Thanks in advance

Should start a new post with the model and a description of the problem as you currently have a junk screen unless it’s fixed.

You have either a failing component in the power section or a failing component downstream drawing too much power, without a detailed visual inspection combined with probing suspect components for failure you aren’t going to get anywhere, unless your screen has a very well known failure point so you can throw parts at it.

Very common for folks to id and replace all caps (even diodes) blindly but that can turn out to be a big waste of time if it’s something more serious.

Thanks for helping out!
Just asked in case the extra information could pinpoint something obvious, but It seems the only way is by opening the monitor and testing components one by one to see if they are working within specs, something I simply cannot do due to the lack of space and proper tools, at least for now. If I ever come back to messing with this CRT, for sure I'll open a new topic here.

LO-RES, HI-FUN

Reply 52 of 64, by spunky_h0rn

User metadata
Rank Newbie
Rank
Newbie

I don't play games like I used to, but I use CRTs when it's era appropriate. Doing this just "feels" right. I generally prefer the look of a high end multisync to any LCD, but I don't daily a CRT any more for my desktop PC so that I don't wear out the tube prematurely.

For console games, I have a quaint little Panasonic, I think it's 13 inches. A great size for the PS1! Barely enough for Timesplitters multiplayer. A friend is hooking me up with a 19" soon, and the Panasonic will be a travel TV for events.

I used to have one of the later 27" Trinitrons, but I don't like big NTSC tubes and I really don't like flat tubes. That went to a buddy who has it playing movies. He's having a lot of fun with it.

I'm committing myself to fixing any of these that ai can get my hands on - I have some experience with my Gateway, but I want to learn more. I have taken on someone's failing CRT, I believe it's a Compaq, whose image is shrunken horizontally. I worry this might be flyback problems but I'll know once I have my hands on it. But, if I'm good or lucky, I can get it working fine, since the tube looks fine.

If all of these go poof one day... I think I'll be alright, even if I don't want to admit that. I can live with an upscaler and dumb chunky pixels on an LCD or whatever. Losing the unique qualities of the tube, though, and not being able to share it, that will be a shame.

GA-M61SME-S2 + Athlon 64 x2 4400+ + 2GB DDR2-800 + ATi 3870
GA-6BXC + Pentium II 300 + 512MB PC-133 + nVidia TNT
GA-686BX + Pentium III 550 + 256MB PC-133 + nVidia TNT2 M64
Soon -> Socket A, Socket 7

Reply 53 of 64, by cloverskull

User metadata
Rank Member
Rank
Member

Dumb question (from an even dumber person) but are CRTs able to be maintained indefinitely or are they all going to become obsolete at some point? I love my CRT and don't want to use an LCD for my retro purposes but I'm nervous about it lasting long even though it works perfectly for now.

Reply 54 of 64, by kixs

User metadata
Rank l33t
Rank
l33t

They were obsolete at least 15 years ago. You can repair it as long you can get the parts. But usually if something essential goes bad it will be either very expensive or even not possible to repair it. That's why I begun slowly reducing my collection of CRT monitors and TVs. I still have around 30 of them. Plan is to have around 10 good ones in my collection. But in reality it will be around 15-20 😁

Visit my AmiBay items for sale (updated: 2026-03-23). I also take requests 😉
https://www.amibay.com/members/kixs.977/#sales-threads

Reply 55 of 64, by Jo22

User metadata
Rank l33t++
Rank
l33t++
cloverskull wrote on 2026-09-11, 06:58:

Dumb question (from an even dumber person) but are CRTs able to be maintained indefinitely or are they all going to become obsolete at some point? I love my CRT and don't want to use an LCD for my retro purposes but I'm nervous about it lasting long even though it works perfectly for now.

No, not dumb at all. There are two parts that are rare: the CR tube and the matching flyback transformer.
The power supply can be substituted, but needs a bit of adapting.
A worn CRT can be "upcycled" by rejuvination, also; giving it some extra years.

https://blog.timowens.io/crt-rejuvination/
https://www.youtube.com/watch?v=YikOY8WTnLU

"Time, it seems, doesn't flow. For some it's fast, for some it's slow.
In what to one race is no time at all, another race can rise and fall..." - The Minstrel

//My video channel//

Reply 56 of 64, by jmarsh

User metadata
Rank Oldbie
Rank
Oldbie
cloverskull wrote on 2026-09-11, 06:58:

Dumb question (from an even dumber person) but are CRTs able to be maintained indefinitely or are they all going to become obsolete at some point? I love my CRT and don't want to use an LCD for my retro purposes but I'm nervous about it lasting long even though it works perfectly for now.

Sooner or later the phosphor coating will suffer from burn-in and/or the electron guns in the tube wear out. Both lead to dimmer colors.

Reply 57 of 64, by The Solutor

User metadata
Rank Member
Rank
Member
jmarsh wrote on 2026-09-11, 09:52:

Sooner or later the phosphor coating will suffer from burn-in and/or the electron guns in the tube wear out. Both lead to dimmer colors.

Usually that's a problem only for monitors powered on h24 for years, or for poorly calibrated ones that run out of specs for long time.

Modern CRTs usually are robust enough to outlive to the line transformer/the voltage triplicator (if present)/and the usual dried electrolytic capacitors.

Once the CRT were guaranteed for 10000h operation but that was 60+ years ago

Reply 58 of 64, by Tiido

User metadata
Rank l33t
Rank
l33t

The cathodes in the gun wearing out are the primary limiting factor of the lifetime. A good tube has about 40k hours of life, that is roughly the point where the video amplifiers are no longer able to counteract the reduced emission and you get problems with not reaching cutoff(tinting in dark areas) and unable to get good focus (beam current must be too high for good brightness and amps just struggle). The rejuvenation can temporarily help, the process essentially overdrives the filaments for a set amount of time, with intent to redsitribute some of the cathode material. Depending on wear, it can give a few years (on mildly worn tube) to just some months or even barely days (End of life tube).

Phosphors burn in is a much smaller concern compared to the cathodes, it happens but that process is rather slow and depends a lot on actual image content. Windows taskbar is a big offender 🤣

Flyback dying is usually the ultimate death, since replacements are basically unobtanium. Sometimes you are lucky and can find something, although at huge cost... If you know what you are doing, it is not impossible to adapt something else in place of the original, but that takes effort and knowledge about the device and a good handful of parts must change in the process. I have done this with some TVs but not yet with a monitor. TVs are much simpler than monitors on this regard.

T-04YBSC, a new YMF71x based sound card & Official VOGONS thread about it
Newly made 4MB 60ns 30pin SIMMs ~
mida sa loed ? nagunii aru ei saa 😜

Reply 59 of 64, by The Solutor

User metadata
Rank Member
Rank
Member
Tiido wrote on 2026-09-11, 11:08:

Phosphors burn in is a much smaller concern compared to the cathodes

Phosphor burn was a problem in the very early BW TVs, you got a dark circular area in the center of the screen, which was due it was hit by ionized atoms rather than electrons. They were heavier than electrons, so they were deflected less by the deflection coils.

Initially the problem was solved by the ionic trap: essentially the cathode was angled, then the aim was corrected by the trap (a magnet placed on the neck of the tube), again the electrons were deflected in the opposite direction correcting the cathode offset, the ionized atoms were deflected less and ended to hit the side of the tube, rather than its center.

After that era the problem was definitely solved using a layer of aluminium, on the back of the phosphors (perhaps the ionic trap would have been an insurmountable problem for color CRTs), and the ionic trap went the way of the dodo, and most phospor problems disappeared as well.

The rejuvenation can temporarily help, the process essentially overdrives the filaments for a set amount of time, with intent to redsitribute some of the cathode material. Depending on wear, it can give a few years (on mildly worn tube) to just some months or even barely days (End of life tube)

Frankly I never had to use it on monitors, either because not needed or because the general condition and residual value discouraged the procedure, but on TVs I often had great results, often the TV had more life after the procedure than before. The small price to pay was usually a slight loss of focus, in some cases a small loss of focus that was uneven across the three main colours, given to obtain a white image the RGB cathode don't work at the same current, so (usually) they wear in a uneven way.

That said I had a expensive regenerator that used any known trick (ultrasounds, voltage impulses...) to revive the cathodes.

Nowadays there are few surviving companies that literally rebuilds the cathode, cutting out the tube's neck, replacing it with a new one, restoring the vacuum and calibratiing the tube, but (I guess) the price of the operation is for real collectors rather than kids interested in retrocomputing